You will need: Glass cabinet, # 15, junk shop Sandpaper Damp cloth Masking tape Ronseal One
Coat White Primer & Undercoat, # 4.98 for 250 ml, B&Q Paintbrush Ronseal One Coat Red Rose gloss cupboard paint, # 18.98 for 750 ml, B&Q Colours Cocktail wallpaper, # 12.98 per roll, B&Q Scissors, PVA glue
Not exact matches
And sometimes in a new home like ours, all you get is a nice
coat of off
white primer, which is susceptible to brush and hand prints.
When it's dry, apply a
coat of
primer and two
coats of the
white roof paint with a long - handled roller, allowing the layers to dry after each application.
I used a few
coats of my #kilz
primer and then #generalfinishes antique
white.
Once that dried I went over those spots with a light
coat of
primer and used four
coats of Sherwin Williams Alabaster
white to give it a nice
white finish.
Spray several light
coats of
White Dual
Primer & Paint Spray paint on jars until thoroughly covered.
Then I applied 1
coat of
primer and 2
coats of antique
white latex paint.
Once the
primer white dries start painting the soles with the color of your choice (do two
coats but be sure to let the first
coat dry before starting on your second
coat).
Vicki decided she wanted it painted
white, so we threw on a coat of primer then a couple coats of Annie Sloan Old White chalk p
white, so we threw on a
coat of
primer then a couple
coats of Annie Sloan Old
White chalk p
White chalk paint.
I'm excited that General Finishes is providing me with
primer, General Finishes Milk Paint in Antique
White and a super strong top
coat to get the job done.
Below is the same table after one
coat of Zinsser Spray Shellac and a
coat of Old
White - which is a paint that does not require a
primer to stick to the shellac.
Basically, you are suppose to use 1
coat of
white paint as a
primer and then 1 - 2
coats of a paint color that is similar to mint / light greenish blue diluted with water to a wash - like consistency.
It's then given several
coats of
primer (very often a
white acrylic
primer called gesso) to seal it and prevent the oil from the paints soaking through the surface.
Silicon bronze and paint (3 - part catalyzed acrylic,
white primer,
white base
coat, «Xtreme» Flat Finish Klearkote), 111 x 102 x 102 inches.
Firstly, a
primer is applied before a
white masking layer is
coated onto the body.
I gave the table a
coat of
primer, and then painted it with General Finishes Milk Paint in Antique
White.
We used shiplap in parts of our home and painted 2
coats of
primer under our
white paint.
I feel your pain...... painting woodwork was brown, doing
white 2
coats of
primer and 2
coats of
white.....
I used one
coat of Kilz
primer and three
coats of Simply
White latex paint.
After I finished painting the legs, I sprayed the top of the table with a couple
coats of spray
primer, and a couple of
coats of Heirloom
White - colored spray paint.
I simply used a
coat of Zinsser
primer and a
coat of
white trim paint.
To make it all work together we primed it all with a
coat of
primer and then covered that with a
coat of
white paint (just run - of - the - mill
white paint out of the can).
We took home one pack of planks that day, and I promptly laid them out on a drop cloth and gave them two
coats and
primer, and two
coats of leftover Moonlight
White (BM) paint.
A
coat of
primer, two
coats of
white semi-gloss, two
coats of Polycrlic, and a
coat of Liquid Leaf later... I was left with this.
For example, if I had used a
white primer, it would have taken multiple
coats of black paint to cover it.
We used three
coats of
white paint (surprisingly, we didn't need
primer.
It was a lot of spraying of
primer (that I added paint thinner to in order to thin it down for the sprayer) and then a
coat of
white.
The first
coat was bright
white semi-gloss paint &
primer (the same can that I use on baseboards and trim), applied with a brush.
Spray several light
coats of
White Dual
Primer & Paint Spray paint on jars until thoroughly covered.
Below is the same table after one
coat of Zinsser Spray Shellac and a
coat of Old
White - which is a paint that does not require a
primer to stick to the shellac.
Once the
coat of
primer was completely dry, I then used Benjamin Moore Advance in Simply
White to complete the project.
It was still time consuming to give each one a
coat of
primer and
white paint.
, all the trim and one door was sanded down, everything got at least one
coat of
white primer, and then the walls got two
coats of PARA Paints Plantain Chips PF52 and the trim and door got three
coats of PARA Paints Jo Jo Whitewash PF17.
To get good coverage it involved one
coat of Kilz
primer, followed by three
coats of Benjamin Moore «Simply
White».
A light sanding and
coat of
primer meant it was ready for a couple
coats of
White Dove (OC - 17).
If I am painting an old piece
white — I use one
coat of Kilz Original
primer on it.
(insert eye roll here) I used Valspar Reserve that has
primer and paint in one, so it only took two
coats of Ultra
White to cover up this dark wall.
Our standard paint finish is
white semi-gloss inside and outside consisting of base -
coat primer / preservative, undercoat and topcoat.
Once you've given the coasters a few
coats of
primer, paint them
white.
Then the process was easy — just 2
coats of Behr Premium Plus Paint +
Primer in One in Ultra Pure
White in semi-gloss applied with a small roller.
2) Use a
coat of light gray over a lacquer based
primer before applying
white paint.
Lay down a
primer coat of a similar, high opacity paint first, such as Seagull Gray under Snow
White, Buttermilk Yellow under Sunglow, Brick Red under Holiday Red, or Coastal Blue under Royal Purple.