Although numerous efforts are put into cleaning up large oil spills, only 15 to 25 % of the oil can be effectively removed
by mechanical methods.
Not exact matches
I think it's a very dangerous mistake to dispense with our present concerns
by ignoring the narrative of our stress - testing response to the credit crisis, and concluding that our experience over this half - cycle has been a
mechanical reflection of our pre-2009
methods, our present
methods, or some perma - bearish disposition on my part.
Although not specifically intended for pastors, bloggers and other «famous» Christians, the book — written
by a Christian and published
by faith - based publisher Thomas Nelson — details an almost
mechanical method to get noticed in an age of self - promotion.
No part of this Buyer & Distributor Guide may be reproduced, distributed, or transmitted in any form or
by any means, including photocopying, recording, or other electronic or
mechanical methods, without the prior written permission of Gluten Intolerance Group of North America, except in the case of specific noncommercial uses permitted
by copyright law, if any.
Based on computational studies, compared to conventional carbon nanotubes, the nanothreads produced
by this
method may have outstanding
mechanical and electronic properties.
A research team led
by Associate Professor Hai Minh Duong (left) and Professor Nhan Phan - Thien from the Department of
Mechanical Engineering at National University of Singapore's Faculty of Engineering has devised a fast, cheap and green
method to convert fashion waste into highly compressible and ultralight cotton aerogels.
Mechanical engineer Frank van Mierlo, 1366's CEO, says this
method should cut the cost of photovoltaic wafers
by two - thirds.
This year's record - breaking fire season prompted President Bush to propose a plan that would emphasize thinning
by private timber companies, which almost always use
mechanical methods.
Work
by Yeh's group and international collaborators later revealed that graphene made using the new technique is of higher quality than graphene made using conventional
methods: It is stronger because it contains fewer defects that could weaken its
mechanical strength, and it has the highest electrical mobility yet measured for synthetic graphene.
She has transformed the field of metamaterials
by designing new
methods to engineer three - dimensional hierarchical nanolattices with remarkable
mechanical, thermal and optical properties.
Despite being conceptually simplistic, the single - cell transfection methodology as a procedure allows transfer of only a few hundred cells, so it has thus been largely replaced
by alternative
mechanical, physical, and vector - based delivery
methods.
No part of this publication may be reproduced, distributed, or transmitted in any form or
by any means, including photocopying, recording, or other electronic or
mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations embodied in critical reviews and certain other noncommercial uses permitted
by copyright law.
There are two main
methods for at - home exfoliation —
mechanical and chemical — and the
method you choose should be guided
by your skin type.
He systematically strips affectation and
method from his performers
by relentlessly drilling them in rehearsals until they master the
mechanical, uninflected motions and line deliveries.
Based on this information, a novice trader, or failing trader should then revert back to practicing a
mechanical method which induces discipline and a step
by step plan.
It was in his sculpture Pyramid (1959) where the figurative was erased
by the
method of stacking identical wood segments in a repetitive form, which like Frank Stella's «black» paintings appeared as if the process had been simply
mechanical.
Although pop art was rapidly succeeded
by other artistic trends, its emphasis on literalism, familiar imagery, and
mechanical methods of production would have a tremendous influence on the art of the following three decades.
The artist arrived at his exacting, almost
mechanical, painterly
method by way of his pursuit of a Neue Sachlichkeit, an impersonal means of image - creation.
He thrived on the increasing confusion between high art and progressive popular culture and the challenge to conventional
methods of painting
by the techniques of
mechanical reproduction.
Digest: A lawyer may pay a for - profit service for leads to potential clients obtained via a website on which potential clients provide contact information and agree to be contacted
by a participating lawyer, as long as (i) the lawyer who contacts the potential client has been selected
by transparent and
mechanical methods that do not purport to be based on an analysis of the potential client's legal problem or the qualifications of the selected lawyer to handle that problem; (ii) the service does not explicitly or implicitly recommend any lawyer, and (iii) the website of the service complies with the requirements of Rule 7.1.
A lawyer may pay a for - profit service for leads to potential clients obtained via a website on which potential clients provide contact information and agree to be contacted
by a participating lawyer, as long as (i) the lawyer who contacts the potential client has been selected
by transparent and
mechanical methods that do not purport to be based on an analysis of the potential client's legal problem or the qualifications of the selected lawyer to handle that problem; (ii) the service does not explicitly or implicitly recommend any lawyer, and (iii) the website of the service complies with the requirements of Rule 7.1.
Except in the case of (1) brief quotations embodied in media coverage of this publication and certain other noncommercial uses permitted
by copyright law and (2) links back to the www.icitech.org website, no part of this publication may be reproduced, distributed, or transmitted in any form or
by any means, including photocopying, recording, or other electronic or
mechanical methods, without the prior written permission of the publisher.
Develops
mechanical and electromechanical products
by studying customer requirements; researching and testing manufacturing and assembly
methods and materials; soliciting observations from operators.
Designs
mechanical and electromechanical products and systems
by developing and testing specifications and
methods.
• Set up production equipment at the beginning of each shift to suit the type of production process to be managed • Calibrate production equipment to ensure appropriate production processes • Measure and mix ingredients and put them into production equipment for processing purposes • Clean and maintaining measuring instruments and equipment and ensure that any
mechanical problems are timely sorted out • Document nonconformance and dispositions
by using set quality control
methods • Assemble goods on the production line and ensure that products are finished according to set protocols • Separate different items and ensure that they are loaded into the production equipment in the appropriate sequence • Pack and label end product according to company protocols and ensure that it is stored properly • Perform preventative maintenance on production equipment and tools
Description The Dish Machine Operator (DMO) / Utility is responsible for maintaining the cleanliness and sanitation of all glassware, tableware, and cooking utensils / vessels
by using both
mechanical and manual cleaning
methods in...
Mechanical Engineer — Regional Engineering Co. — Decator, Alabama — April 2000 — September 2009 • Developed new
methods to accelerate production speed
by at least 23 percent • Collaborated on all phases of design process for a variety of products, including components, assemblies, subassemblies, and parts • Completed designs, including drafting, dimensioning, and documenting results • Designed parts for existing machinery to improve functionality and extend life of equipment • Received commendation for assessing and improving complex product specifications and resolving manufacturability concerns • Identified and corrected flaws in existing injection molding designs
I want to pursue a career in
mechanical engineering
by sharing my theoretical and practical knowledge, skills, and various
methods of applied science to enhance your organizations processes towards achieving complete client satisfaction and try to meet every organizational objective.