Not exact matches
• clean and sterilise all feeding parts before each use • do not use abrasive cleaning agents or anti-bacterial cleaners with bottles and teats • wash your hands thoroughly and ensure
surfaces are clean before handling sterilised components • for inspection of the teat, pull it in each direction • place the teat in boiling water for 5 minutes before first use to ensure hygiene • throw away bottle and teats at the first sight of damage, weakness or scratching • replace teats and spouts after 3 months use • do not warm milk in a microwave as this may
cause uneven heating and could scald your baby • always check the milk temperature before feeding • make sure that the bottles are not over-tightened • do not allow your baby to play with small parts or run or walk while feeding
This could
cause the toddler bed
surface to be
uneven causing discomfort to your young one.
One of the four metal brackets that connect to the mattress support can break,
causing a gap and an
uneven sleeping
surface for the baby.
This helps you jog on
uneven surfaces and on bumpy roads without
causing any kind of discomfort for your kids.
Running on
uneven surfaces, biomechanical flaws, imbalance of strength in the muscles, and not enough recovery time are some of the most common
causes for knee related injuries.
Fine lines and wrinkles can appear more noticeable, skin texture can look rough and
uneven, and it can
cause dead skin cells to buildup on skin's
surface.
According to the HSE, the majority of trips are
caused by obstructions in walkways, while the rest are
caused by
uneven surfaces.
The springs, torsion bars, shock absorbers, linkages and locating members acting together to control motions
caused by tires passing over
uneven road
surfaces to reduce the effect on the vehicle body.
Without the ability to move and flex with the
uneven road
surfaces and bumpy roads, the vehicle would be difficult to control, hitting the bumps solidly, which would
cause the wheels to leave the ground in a vertical bounce and land with a crash.
By plumbing the car's damping this way, Audi can quell much of the pitch and body roll
caused by
uneven surfaces or during very hard driving.
3 Affecting
Surface Currents Wind —
Caused by the
uneven heating of the atmosphere, variations in wind temperature lead to variations in air density and pressure.
Adiabatic uplift and descent does that job via
uneven conduction from the
surface causing density differentials which then give rise to the necessary convection.
Wind is
caused by the
uneven heating of Earth's
surface.
Even if you're an experienced rider who has braked before entering a turn and accelerated into it, you can be taken unaware by oil spilled on the road or an extremely
uneven surface that
causes you and your motorcycle to capsize.
Another common
cause of motorcycle accidents throughout the state of California is road hazards — debris,
uneven road
surfaces, small objects, cracks, potholes, wet leaves and wet pavement.
While slip and fall injuries commonly occur due to
uneven or slippery
surfaces, accidents can also be
caused by broken steps, raised flooring, ripped carpeting, poorly lit walkways, cluttered pathways, and inadequate warning signs.
A slip and fall or trip and fall injury occurs when your foot makes contact with an
uneven, slippery, unstable or loose
surface that
causes you to lose your balance and fall down.
Cases can develop from many other situations: slip and falls on a slick
surface or ice; defects in roadways such as missing road signs, bad intersections or pavement defects; holes or
uneven surfaces in parking lots, sidewalks or floors; unmarked drop - offs, ledges, culverts or holes, dangerous retail layouts or designs, including sharp corners and displays that may
cause injury to children.
Most common
causes of slip and fall injuries are
uneven ground
surfaces, potholes, ripped carpeting, cracked cement and wet floors.
Slip and Fall Accidents are often
caused when an object is in your path, issues with the walkway like wet walkway, and more conditions like: —
Uneven surfaces — Slippery and wet floors — Broken railings — Raised or broken side walls — Inadequate lighting — Unsecured carpets — Narrow stairs
A slip and fall can be
caused by weather conditions, wet or
uneven surfaces, defective walkways or stairways, and other conditions on business property.
Trip and falls are
caused by objects or
uneven surfaces, and occur when your feet collide with an object,
causing a loss of balance.
This is because of their large size and as they are close to the hard and
uneven surfaces of the skull that can
cause damage.