Sentences with phrase «drill pocket holes»

If you are making multiple cabinet doors, create an assembly line: cut all the stiles & rails, add the routered grooves, cut panels, drill pocket holes, then assemble.

Drill pocket holes for 3/4 ″ material on the outside back of the drawer sides.

Drill pocket holes for 1/2 ″ material on the outside front of the drawer sides (remember the front of your drawer is only about 3/8 ″ -1 / 2 ″ thick because of the decorative cuts).

Before assembling the legs, drill pocket holes for 3/4 ″ wide material in the top of the legs and leg sides.

Drill pocket holes on the back side of one of the boards.

Drill pocket holes on the back side of the front piece and connect the sides with 1-1/4 ″ pocket screws and glue.

Use a pocket hole jig to drill pocket holes in the ends of the supports and attach one at the top and bottom and one in the middle.

If you are using pocket holes, drill all pocket holes.

Cut 2 pieces of 3/4 ″ plywood to 10-3/4 ″ x 9 ″ and drill pocket holes around the edges.

Use the Kreg Jig to drill pocket holes on the back of the first 4 boards — approximately 2 inches in on each side.

First, cut all your 1 x 6 pieces then drill pocket holes with the Kreg Jig as I've shown below.

Once the walnut was cut, we used a Kreg Jig Master System to drill pocket holes and added screws to secure the walnut boards together to form a top to cover the island.

First, cut all your 1 x 6 pieces then drill pocket holes with the Kreg Jig as I've shown below.

I definitely recommend reading the instructions yourself and maybe checking out a few YouTube videos, but to give you a very basic idea of how it works: Measure the thickness of the wood you're drilling the pocket holes into.

You will notice I have drilled the pocket holes for the front and side pieces.

After her eldest drilled pocket holes and screwed them into the wall, the youngest sanded down all the edges of the boards.

My oldest drilled pocket holes and helped screw them into the wall, the 6 year old marked which board was for what, and placed the pocket hole screws in the holes, and my youngest sanded all the edges of all the boards.

Once I cut the boards to size, I drilled pocket holes along the edges using my Kreg Jig.

Not exact matches

Then they bored tiny holes into the crystals with sterilized drills to reach a pocket of trapped brine.

Our cheap dissertation proposal writing UK makes sure that the services offered by our company never drills a hole in the pocket of our students as they always have financial limitations.

Drill 3 or 4 pocket holes down the length of the boards (on the underside only).

Then I drilled two pocket holes on each end of the aprons.

Before attaching the support pieces to the wall we used the Kreg Jig to drill 2 pocket holes in each piece for the location where we planned to use Kreg Jig screws to attach the support piece to the countertop.

Drill 3 - 3/4» pocket holes in both long sides of one of the side panels.

Drill 4 - 3/4» pocket holes on both 19 1/2» sides of the back panel.

Drill a single 3/4» pocket hole on either end of all three drawer dividers.

Then drill 3/4 ″ pocket holes into the 9 3/8 ″ long 1x2s.

To build the shaker - style doors, simply drill 2, 1/2 ″ pocket holes along all four sides of the 1/2 plywood.

Drill 2, 3/4 ″ pocket holes on either end of the 1x2s for the front and back of the bottom shelf frame.

Drill 3/4 ″ pocket holes on sides of 3/4 ″ plywood (the long sides of the 17 1/8 ″ x 12 1/2 ″ pieces) and 1x2s.

You could make this whole table with just a miter saw, a pocket hole jig and a drill, but I'll show you some of the ways I used other tools to get what I think is a better look.