Not exact matches
It didn't
need a full tune up so I poured a
fuel injector cleaner into the gas tank and filled the tank with gasoline.
If diesel does get to the engine you'll
need to drain the
fuel system and clean, possibly replace the
injectors.
Diesel
injectors require high pressure
fuel in order to achieve proper atomisation; liquids don't burn, so the
fuel needs to enter the cylinder in very fine droplets in order for a clean burn to...
Diesel
injectors require high pressure
fuel in order to achieve proper atomisation; liquids don't burn, so the
fuel needs to enter the cylinder in very fine droplets in order for a clean burn to occur.
For this, you'll
need a better quality
fuel pump, bigger
injectors and a software update.
This is a great video that will teach you everything you
need to know about replacing a bad intake manifold, or
fuel injector.
You would
need to pull the
fuel rail, leaving the
injector on the rail, then pressurize the system looking at whether it dumps
fuel without the engine running to tell if this is an issue.
Other than 2 engine warning lights that came on within the last 12 months where it
needed to be reset, a
fuel injector failed a month ago.
The battery is
needed to power your
fuel injectors, spark plugs and other auxiliaries.
The engine ECU powers the actuators on the vehicle, so you
need to check things like:
fuel pump runs when ignition key is turned to the run position, power to
injectors, power to ignition coils, brake lights working.
Low
fuel pressure can cause the
injectors to drip
fuel instead of spray it and of course the engine will have less
fuel than it
needs.
This way you make the
injector squirt the
needed fuel during the entire intakestroke, giving a better homogenized charge entering the cylinder.
Fuel injectors and fuel pumps from Bosch provide the extra gasoline you need on your high - performance buildup, along with legendary Bosch qua
Fuel injectors and
fuel pumps from Bosch provide the extra gasoline you need on your high - performance buildup, along with legendary Bosch qua
fuel pumps from Bosch provide the extra gasoline you
need on your high - performance buildup, along with legendary Bosch quality
But this will not be enough, you will have to increase the compression ratio to 11, which means that you
need to buy high compression pistons, lightweight connecting rods, a lightweight flywheel and H22A
fuel injectors.
In this case you
need GT3540 turbocharger, and also camshafts 256/256, valve springs and
fuel injectors 750 cc / min.
To increase the power considerably, you
need to purchase performance cams (duration 272/272), valve springs, cam gears, rod bolts, high compression forged pistons,
fuel injectors 440 cc, new spark plugs, performance MAF sensor, Kinetix intake manifold, cold air intake, equal length headers, performance exhaust system, Motec ECU (or reflash stock ECU).
To increase power even more, you will
need to buy additionally to the above mentioned STi Group N engine mount set, a 3 - row Mishimoto radiator, sump baffle plate, 1000 cc
fuel injectors, Garrett GTX 3076R turbocharger, wastegate tial 44 mm, Aeromotive
fuel regulator,
fuel lines.
If you are the owner of EJ255, then you
need some modifications such as aluminum 2 - row Mishimoto radiator, FMIC, EJ257 intake system, BOV valve, WRX STI oil pump, new spark plugs, WRX STI
injectors, Walbro 255 lph
fuel pump, ACL bearings, the boost controller, 3 ″ performance exhaust system.
To get 400 WHP, you will
need a turbo kit based on the GT3076R with an intercooler, NGK 8 Iridium spark plugs, 750 cc
fuel injectors, a Walbro 255 lph
fuel pump, a 3 ″ aftermarket exhaust system, and an AEM EMS ECU.
You will also
need a multi-layer steel head gaskets, wastegate, blow off, boost controller, oil feed line, oil return line, thermal insulation,
fuel injectors 7M - GTE (440 cc / min), pipes, clamps, VEMS ECU.
Action
Need To Fix It: Chrysler will notify owners and dealers will replace the engine
fuel rail
injector crossover hose, free of charge.
Among the highlights of the four - cylinder engine are its direct - injection system with exhaust gas turbocharging, an enhanced combustion system and extended stratification ranges for lean - burn operation using fast - acting
injectors for the multiple
fuel injections, and multi-spark ignition according to
need.
The result is a very stable burn and very good
fuel economy with both
injectors working in concert to adjust torque precisely as
needed to move the load as speed, temperature and terrain change.
Beck Arnley
Fuel Injector Nozzle O - Rings are thoroughly built to carry out vehicle
needs and owners selection since automotive experts carefully toughened and cycled all components for safekeeping and supreme function.
To receive 350 + horsepower, you
need the new
fuel pump,
fuel injectors, pulley and water / methanol injection.
You will also
need an intercooler, a piping kit, a blow - off valve, an oil cooler, a Mishimoto oil catch can, a Walbro 255
fuel pump, 630 cc
fuel injectors, a 2.5 ″ exhaust system, and a Hondata ECU.
You will also
need ARP studs, a Garrett T04e turbocharger, a turbo manifold, an intercooler, HKS BOV, a Walbro 255 lph
fuel pump, a 3 - row radiator, an aftermarket
fuel rail, 680 cc
fuel injectors, an aftermarket
fuel regulator, a wideband air /
fuel oxygen sensor, the 3 ″ performance exhaust system, and a Hondata ECU.
You will
need aftermarket camshafts, adjustable cam gears, high compression pistons (compression ratio ~ 14), a 3 - row radiator, a Mishimoto oil cooler kit, an oil catch can, an AEM
fuel rail, 550 cc
fuel injectors, a TODA light flywheel, NGK 9 iridium spark plugs, AEM EMS ECU, and sports
fuel.
It is also
needed to get a turbo manifold, pipes, intercooler, blow - off, thick cylinder head gasket, 2ZZ - GE
injectors, 1JZ - GTE
fuel pump, and ECU 1NZ - FET / GReddy e-Manage Ultimate.
- Cylinder deactivation: When less engine power is
needed, such as in highway driving, the valves and
fuel injectors in half the engine cylinders are deactivated.
Running a little rough at the moment and
needs a little work (maybe fuel pump or injectors) Needs shocks and ba
needs a little work (maybe
fuel pump or
injectors)
Needs shocks and ba
Needs shocks and ball...
Truck
needs injectors and
fuel lines.
Motor
need fuel injectors.