Sentences with phrase «grit sandpaper»

After a thorough cleaning, I let the table dry in the sun and then gave it a sanding with 120 grit sandpaper.

Start with # 120 grit sandpaper and progress through # 150, # 180 and # 220 grits.

After sanding all the boards with 150 grit sandpaper, I stained with Minwax Dark Walnut for the bottom section of the platform.

We followed with 220 grit sandpaper until it was smooth.

lately I have started using a VERY high grit sandpaper to buff the stain between coats (as opposed to using steel wool) and this has given me very nice results.

1 - Use 150 grit sandpaper and sand the entire floor.

I sanded in between coats with 220 grit sandpaper.

I also sanded in between coats of topcoat with 400 grit sandpaper for a super smooth finish.

This high grit sandpaper will cost you more in the end than using steel wool... which is much cheaper, but to be perfectly honest with you I think using the high grit sandpaper has given my refinished pieces a much finer finish.

Also, lightly sand the flat surfaces with a fine grit sandpaper for a smooth finish.

STEP 1 First lightly sand the entire surface by hand using a sanding block and some fine - grit sandpaper.

Kurt sanded the drawer faces down to the bare wood using 80 grit sandpaper then followed with 220 grit sandpaper until smooth.

Either way you will be fine... using steel wool or high grit sandpaper.....

I do this by going over the paint with a 320 or 400 grit sandpaper.

To create a time worn appeal, distress each table with fine grit sandpaper on the top and edges.

I have been using 1000 grit sandpaper like this 3M Ultra Fine Grit Silicon Carbide Sandpaper.

I use a hand sanding block and 60 - 100 grit sandpaper to rough up the surface a bit.

When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper.

A quick 5 - 10 minute going over with 100 grit sandpaper is all it will need.

I use 100 - grit sandpaper over the surface to rough it up first with a hand - sanding block before painting.

After wiping off any stripping remnants, I sanded the top with 150 and then 220 grit sandpaper.

HIGH grit Sandpaper!

I would run 100 grit sandpaper over the entire surface and clean the grit off, then paint.

I always go over every piece I paint with a sanding block with 100 grit sandpaper on it for about 5 minutes to rough up the surface a bit.

Grab your orbital sander equipped with 120 grit sandpaper and give the top and sides a good sanding until they are nice and smooth.

I would sand the surface with 100 grit sandpaper on a sanding block just to rough up the surface a bit.

Two coats should be plenty — I would run medium grit sandpaper over the surface quickly and then make sure the piece is clean and dry before painting.

After it is dry, use a medium to fine grit sandpaper to sand the top color of paint off.

You don't need to take the finish to the bare wood, but use a hand block sander to rough up the surface with 100 grit sandpaper.

Then I used some 180 grit sandpaper to gently distress the edges and some other areas of the clay hearts.

If it is not binding, but just feels gritty — sanding the surface with fine grit sandpaper will remove any grittiness.

Supplies you will need for a standard 6 ′ wide closet: 2 - 3 ′ wide bi-fold flat panel hollow core closet doors (found at most home improvement stores) 1 - 4» x8 ′ sheets of 1/4 ″ underlayment plywood Liquid nails adhesive 1 ″ nails, 18 gauge Wood filler White interior caulk 220 grit sandpaper

Just use a fine grit sandpaper and go to town.

If the tile is slick and shiny, I would rough it up with 60 grit sandpaper and then clean it well.

Fill nail holes and gaps with wood filler, let dry, and sand entire vanity smooth with 22o grit sandpaper.

The final sanding before paint was with a finer grit sandpaper to ensure the entire unit was smooth.

It took multiple heavy rounds of sanding with coarse grit sandpaper to get the finish off.

I then sanded it down again using a fine grit sandpaper to smooth it out, applied another coat of primer, and then painted the inside Jazzleberry Jam and the outside Jo Jo Whitewash.

When distressing I use a fine grit sandpaper block, but you can actually also distress with a wet rag if you've only done one color and there is wood underneath.

This high grit sandpaper is the type that is used on the side of a corvette to make the fiberglass super smooth!

Once dry, lightly sand with 220 grit sandpaper.

In the areas I wanted the wood of the piece to show - so you and where I used the aggressive grit sandpaper - you can see how I revealed that.

Let dry and sand completely with 220 grit sandpaper.

If you have brush strokes in your paint and you do not like the look them — before applying your wax top coat... consider sanding your surface with some 220 or 400 grit sandpaper.

I generally use 150 or 220 grit sandpaper... but you can even go up into the super fine grits like 600 to really smooth our your surface.

* Then gently polish the piece with the high grit sandpaper.

With a little 200 to 400 grit sandpaper... I will make the front of this piece as smooth as glass!

For your counters, did you sand them before your first coat of Waterlox and if so, what grit sandpaper did you use?

I then sanded the whole thing lightly with 180 grit sandpaper, pressing harder in spots that I was wanted to be more «distressed,» such as on the corners of drawers, and carved or recessed parts.

If I was using latex paint, this would have been a concern for me, but with using Chalk Paint ™, I knew I could take my 200 grit sandpaper afterward, and strategically sand in a lateral direction, and sand down the high points of the paint.