The job profile also
includes drilling holes through interior panels, connecting hoses to evaporator and cool - air outlet, filling compressor with start units and refrigerant, threading hoses through holes and measuring compressor pressure by using gauge.
Work done in the southern hemisphere's summer, December through January 2012 - 13,
included drilling holes in the ice to place a variety of instruments and using radar to map the underside of the ice shelf and the bottom of the ocean.
Work done in the southern hemisphere's summer, December through January 2012 - 13,
included drilling holes in the ice to place a variety of instruments and using radar to map the underside of the ice shelf and the bottom of the ocean.
Not exact matches
Completion of a technical work program in preparation for updates to the 2016 NI 43 - 101 Mineral Resource Estimate («Mineral Resource»),
including completion of 6,324 metres of infill
drilling in 22
holes to close off the infill
drilling program totalling 29,026 metres in 76
holes.
Previous
drilling results at Jubilee
include 5 metres grading 7.34 % copper and 3.75 g / t gold from just 35m down
hole and 4m @ 6.27 % copper and 0.7 g / t gold from 59m.
A total of 11 prospects were identified in 2016 from an initial 28 -
hole, 2,278 m scout
drilling programme, which delivered exciting intercepts
including visible gold in 7m at 24.5 gpt Au at the Lydia prospect.
Narrow high - grade gold and silver intercepts in two
drill holes targeted beneath a mercury soil anomaly located approximately 500 m northeast of the Tokusei mine workings,
included 0.95 m @ 69 g / t gold, 263 g / t silver (13MAHB - 1) and 1.15 m @ 12 g / t gold and 7 g / t silver (13MAHB - 2) 2, at about 300 m and 450 m below surface respectively.
Hole DK -10-02 intersected strong potash mineralization yielding 25.8 % KCl over 5.5 metres (
drilled width) from 150.10 metres to 155.65 metres,
including 34.8 % KCl over 2 metres (
drilled width) from 150.10 metres to 152.10 metres.
At Gold Spec, historic
drill holes including BSD0013 (0.67 m @ 42.9 gpt Au), GSI - 003 (2.1 m @ 17.09 gpt Au) and GSI - 007 (2.1 m @ 20.09 gpt Au) fall along the periphery of the resource model and similarly suggest immediate potential to expand this deposit through offset
drilling.
At Blue Spec, for example, historic
drill holes including BSI - 011 (1.72 m @ 36.78 gpt Au), BSD0027 (1.15 m @ 62.67 gpt Au), BSD0036 - W1 (2.5 m @ 157.45 gpt Au) and BSD0018 - W2 (1.76 m @ 12.57 gpt Au) fall along the periphery of the current resource model and suggest immediate potential to expand this deposit through offset
drilling.
A further 28
holes have been
drilled at L65 deposit, which was
included in the mine plan in the PEA.
All 12 Silver Standard
holes drilled in the mid-1960s intersected nickel - copper mineralization highlighted by a 37.8 - metre interval in DDH -4-1966 that returned 1.3 % nickel and 0.79 % copper,
including 5.9 % nickel and 1.7 % copper over 2.74 metres near the bottom of the
hole.
Drill results from Alacran
include:
Hole ACD006A (109m grading 0.95 % copper and 0.35 g / t gold) and ASA051 (111m grading 1.01 % copper and 0.38 g / t gold).
The comprehensive Sleeper data base now
includes data from 162 core and 4,119 reverse circulation
holes drilled by various operators.
Validations were conducted to review the information of the nearest neighbor for global bias and drift, whereas for the general neighborhood review (where blocks around
drill holes are also
included), composited samples of 1.5 m were used.
Below, first select between flat - bottomed or standard round, then which
drilling pattern you require (if you require a special
drilling pattern, please contact us first), then select untrimmed or Alcantara trimmed (note: the flat - bottomed 330 is only available trimmed), then select whether you require 2, 3 or no button
holes and finally select whether you require the steering wheel to be able to accept a Farringdon ST8600 display (not
included).
Includes Hitch Platform With Tray To Accept Ball And
Drilled Box
Holes With Caps Installed
You will need to
drill a
hole in the bezel of your tailgate handle for the
included low profile camera to pass through.
Includes Hitch platform with tray to accept ball and
drilled box
holes with caps installed, box mounted 7 - pin trailer harness (similar to (UY2) harness).
This camera mounts into your factory grille by
drilling a single
hole in your upper cross member, then run the harness to the cab and connect to your factory MyFord Touch screen using the
included 8» SYNC 2 interface module.
They can swing around the level with a grappling hook and use weapons
including a flamethrower, a
drill, and a thing that fires black
holes.
Andre did call a series of assemblages Dada Forgeries,
including a book with a three - inch
hole drilled right through it and a pack of Camels.
This solo exhibition
includes lovely perforated mirrors — the
holes were
drilled along the reflections of the artist's studio furniture — and spools of nylon thread, whose length corresponds to the distance between two meaningful sites, i.e. his house and his gallery show.
A bore
hole drilled or being
drilled for the purpose of or to be used for producing, extracting or injecting gas, petroleum or another liquid related to oil or gas production or storage,
including brine disposal, but excluding a bore
hole drilled to produce potable water.
If you have a concrete or brick wall, use the
included drill bit to make your pilot
holes and hammer in the
included wall anchors before you drive in the screws.
If your exterior is wood, all you need to do is
drill pilot
holes using a
drill bit that's a tad smaller than the
included screws.
If the exterior of your house is brick or masonry, you'll need to use the
included drill bit to
drill holes where you made marks, and then insert in the two yellow wall anchors before screwing on the mounting plate.
For new owners, installation is pretty simple: just
drill four well - placed
holes where you want the doorbell to live, then use the
included wall plugs and screws to fix it in place.
There will be a variety of nice - looking Qi charging pads (
including wood ones), as well as an insert that you can
drill a
hole into a current desk or table to add.
• Performing assembly measures as per specifications • Installing moving parts
including shafts, levers, or bearings, and working them to test free function • Bending and installing pipe for hydraulic systems • Removing minute quantities of metal to clean parts or to make close fit among parts •
Drilling, taping, and reaming
holes • Bringing bolts, screws and gears into line, and fasten them together