Sentences with phrase «injectors operating»

Fuel is supplied by the latest generation of common - rail fuel injection using piezo - injectors operating at a maximum pressure of 1,800 bar.

The fuel injection system with magnetic valve injectors operating at a pressure of up to 1,800 bar ensures precise dosage of fuel as well as a consistent, low emission combustion process.

Fuel is supplied to the unit using Bosch 3rd - generation common rail direct injection (CRDi) through piezo - electronic injectors operating at 1800 bar, with air being fed through an electronically managed variable geometry turbocharger and an advanced engine control unit (air system - based charge control).

A new common rail system with piezo injectors operating at a pressure of 2,000 bar, high - efficiency exhaust gas recirculation and further optimised turbocharging join forces to achieve a significant reduction in untreated emissions.

With its all - aluminium power unit, the BMW 740d xDrive boasts BMW TwinPower Turbo Technology as well as common - rail direct fuel injection with its piezo - injectors operating at a pressure of up to 2,000 bar.

Fuel is delivered by the latest generation of piezo - injectors operating at a maximum pressure of 1,800 bar.

The way steam injectors operate creates a compromise between heat up times and efficiency because as you increase the flow rate of steam, more is lost into the atmosphere as it bubbles straight through the product.

Opening up to the outside, the injectors operate at a pressure of up to 200 bar, distributing fuel in a conical spray pattern throughout the entire combustion chamber.

The intercooler is built into the inlet manifold, located at the front of the car, and the port injectors operate at lower engine operating speeds to deliver better fuel charge formation when the fuel and air charge is created in the inlet ports.

Not exact matches

An all - new injection system operates at more than 5000 p.s.i. and incorporates smaller injectors to deliver smaller fuel droplets, improving combustion.

Test - drive the vehicle to get the engine up to full operating temperature in order for the new injector shutdown cleaning cycle calibration to be effective.

The injectors need 500psi minimum to operate.

Since they do not rely on pressurized fluid to operate, it is my guess these may be push started, provided or course, that there is enough juice in the battery to provide a spark and operate the fuel injectors.

Each injector has a solenoid operated by an electronic control unit, resulting in more accurate control of injector opening times that depend on other control conditions, such as engine speed and loading, and providing better engine performance and fuel economy.

The most powerful diesel version of the compact BMW X model features a four - cylinder engine with TwinPower Turbo technology and Common Rail direct injection, the piezoelectric injectors of which operate at a maximum pressure of 2,000 bar.

The fuel injection system operates at pressures of up to 200 bar, and its five - hole injectors can deliver up to three injections per operating cycle.

Piezoelectric injectors are capable of operating up to five times per cycle, which helps reduce engine noise, fuel consumption and particulate emissions.

The turbocharged 3.0 - litre six - cylinder unit uses a new injector system that operates at 2500bar.

A cross-flow cooling system in the cylinder head ensures that the spark plugs and injectors always operate in the most favorable temperature range.

With the help of an injector, the fuel is injected into the cylinders at an angle of 30 degrees and, depending on the engine operating characteristics, at a pressure of up to 140 bar.

Its operating principle involves applying mechanical pressure to a non-conducting crystal to produce an electrical impulse; in turn, this impulse is so fast that it significantly reduces the injector's response time.

The system operated at 350 kPa and used Multec II injectors that were more precise than past injectors.

Fuel is supplied by means of upgraded piezo injectors now operating at a maximum pressure of 1,800 bar.

Like the 2.0 D - 4D engine, it also benefits from improved piezo - electric fuel injectors, operating at higher pressure — increased from 1,800 to 2,000 bar.

Dual pre-injection is used to optimise combustion noise in wide operating ranges, and the injectors are sealed in their shafts.

The common rail direct injection system operates at up to 2,000 bar, with fuel entering the combustion chambers through eight - hole injector nozzles.

EXPERIENCE Radiology Technologist September 2008 - September 2009 Godwin Corporation, Tripler Army Medical Center, HI Proficient in all clerical aspects of radiology to include patient check - in, informed consent, and use of CHCS and PACS programs Fluoroscopic exams to include pediatric and adult barium enemas, esophagrams, G.I. studies, VCUG's, HSG's, and modified barium swallows Use of portable C - arm in operating room procedures to include orthopedic, spinal, abdominal, urologic, vascular, and interventional radiology cases Operation of stationary C - arm in upper and lower extremity arthrogram studies and lumbar punctures Preparation of contrast material for gastrointestinal, gynecological, urologic, intravenous and intra-arterial studies Inpatient and outpatient diagnostic x-rays to include upper and lower extremities, cranium, chest and abdomen Proficient in emergency patient care protocol to include CPR, oxygen administration, suction and use of monitoring systems such as EKG and blood pressure equipment Adherence to all radiation protection standards in accordance with ALARA Instruction of Army Radiology students in all aspects of radiography Radiology Specialist (Active Duty) February 2008 - July 2008 U.S. Army, Tripler Army Medical Center, HI Diagnostic radiographic imaging using digital, portable, C - arm and plain film systems Fluoroscopic, orthopedic and operating room radiography utilizing GE, Siemens, Canon, and Fuji equipment Interventional procedures to include aortograms, peripheral and cerebral angiography, venography, femoral runoffs, arthrograms, fistulagrams and lumbar punctures Preparation and set up of sterile field and instruments for interventional and fluoroscopic procedures using proper sterile technique Proper set up and use of intra-arterial and intravenous injector systems Experience with reconstruction, subtraction, road mapping and duplication of digital images Orientation to additional radiology modalities such as ultrasound, MRI, nuclear medicine, CT and mammography