Sentences with phrase «lean condition»

But, realistically, those numbers represent the maximum measurements that such a natural trainee is likely to achieve in lean condition without drugs, while still maintaining balanced measurements throughout the body.

The valves may have carbon built up on them and will cause lean conditions.

The faulty sensor can cause a too rich or too lean condition.

Also, CO2 is low, indicating lean conditions.

Feed the amount of food that keeps him in good lean condition, even if it is less than the pet food manufacturers recommend.

On the strength of these correlations, data was fit and a set of equations that predict muscular measurements in lean condition of approximately 8 % to 10 % body fat was derived.

That will confirm if the too lean condition, that has caused the codes to set, affects all or just a few cylinders, and in which bank of the engine.

If you reach 95 % of most of these predictions - in lean condition - you will stand out in almost any gym.

Here is a post related to troubleshooting rich and lean conditions with your carburetor set.

This problem can actually affect the gas mileage as you will be sucking in oxygen at the leaks which confuses the O2 sensors into telling the computer to dump more fuel (it reads a false lean condition).

Which indicates lean conditions on both banks.

The giveaway on most lean conditions is the falling idle.

Could be the o2 is faulty try inducing a rich or lean condition at idle.

That being said, if you give one cylinder a super lean condition and the other a super rich one you can effect the synchronization.

If the engine is port fuel injected and the injector for that cylinder was not allowing the proper amount of fuel, you'd have an extreme lean condition in that cylinder, which could cause severe detonation.

Carb Cleaner Test, there's a troubleshooting lean condition section toward the bottom of the answer.

«Many school libraries are operating under lean conditions, which makes it difficult for them to introduce digital innovations and resources which can influence learning and literacy outcomes.»

From 2000 to the end of El Nino conditions in the spring of 2010, despite a lot of La Nina / La Nina leaning conditions during that period, there was fairly pronounced warming — red trend line.

Also dirty clogged injectors can cause lean conditions as well.

One of the most common problems tuners face is a melted piston, which is caused by a too lean condition in the combustion chamber.

Be careful of CAI setups - they often change the MAF curve in a bad way, because altering the plumbing may change the laminar flow in the very small sensor cross section where the actual sensor is, usually creating a false lean condition.

This means that your beloved companion may die sooner than if he was in lean condition.

Most commonly, if a person reaches these predictions, yet still doesn't appear muscularly impressive, then he's simply too fat - keep in mind that these equations describe a lean condition.

The lean condition combined with a late spark left some of the lean over oxygenated intake charge still burning when his exhaust valves began to crack open.

With one cylinder pumping air into the exhaust the mixture sensors (oxygen sensors) will see this as a lean condition and try to compensate by enriching the others on that bank.

The condition you are experiencing is a lean condition.

In a computer - controlled system (again, I'm not sure how this is implemented in older cars), the computer can try to adjust for a lean condition, caused by more air than is optimal, by adjusting fuel delivery.

At idle if there's more volume than calibrated for, the AFR / O2 sensor will see a lean condition and the ECM adjusts fuel trim to compensate.

In the course of helping my friend sort out a lean condition with his Mercedes GLK280 we have to pinpoint the source of a vacuum leak in the intake plumbing.

Since the intake manifold pressure is directly measured to calculate the intake air volume and decide the amount of fuel to inject, a vacuum leak theoretically can not contribute to a lean condition like this.

If you have unmetered air getting into your system between the butterfly of the carburetor and the cylinder head this will create a lean condition.

Makes a lot of sense, I heard a lean condition can cause it to heat up more too, and the bike was running hotter than usual at idle so this would make sense, gonna go ahead and try to fix the airbox fittings or buy a new one, and start going through the trouble shooting to see if I can find any vacuum leaks, ill keep you updated on my findings!

I've read from other posts that a faulty O2 sensor could cause the lean condition, so I have been...

This would cause a lean condition.

Sounds like a lean condition Here's something to chew on regarding identifying a lean or rich condition on a motorcycle.

If you have a lean condition that suddenly appears...

/ Showing signs of a rich / lean condition?

If you have a vacuum leak you will end up with a lean condition.

Micro-globs of gas pass through the combustion chambers unburned — effectively creating a lean condition in the chambers — so that the O2 sensors add more fuel to the mix, which in turn produces a rich mixture in the exhaust and uneven flame in the chambers.

If burned means the electrodes are eaten up a beat you could be suffering from a lean condition from a vacuum leak or a sensor not reporting properly to the ECU.

A clogged fuel filter can restrict fuel volume causing a lean condition, and set random...

The lean condition could be one of several possible causes.

The rough idle may be due to the fuel injection system being dirty or having an engine vacuum leak causing a lean condition.

That will confirm if the too lean condition, that has caused the code to set, affects all...

An intake gasket leak would allow unmeasured air into the intake and create a lean condition, not an overheating issue.

P0420 could be due to a variety of faults including even a fuel pump that is not supplying sufficient fuel, causing a lean condition, and hence «fooling» the O2 sensors (pre and post) as to the status (i.e., efficiency)...