Sentences with phrase «of coats of poly»

Because we were leaving the pine trim as it was (plus a couple of coats of poly acrylic) I did the same with the upper kitchen cabinets to keep the whole house looking cohesive.

The flooring was existent to the house — red oak hardwood — the floors were refinished during the kitchen renovation and received a couple of coats of poly.

Not exact matches

The seat material is made of Poly and Dobby weave fabrics with water repellent coating and open cell foam padding.

The seat material is made of poly and dobby - weave fabrics with water repellent coating and open cell foam padding.

While the seat material is made of Poly and Dobby weave fabrics with water repellent coating and open cell foam padding.

The seat for this stroller is made of Poly and Dobby weave fabrics with a water repellent coating and open cell foam padding.

And the corners are rounded to reduce the risk of injury, poly coated on the outside to protect the exterior

I inly used two thin coats of poly.

Your table will need several coats of furniture wax or poly, which will cure to a hard, protective surface.

You can however apply wax over a poly coat, to get the hand - rubbed look of the wax with the durability of the poly.

I believe chalk paint would work but you would need to add several coats of wax or a poly to protect it.

I started by giving it a wipe down and sanding the top, then re-stained the top surface with Early American and three coats of non-yellowing water - based poly.

It took about three days — one to lay and stain — the second day in the morning we put on the first coat of poly, a few hours later did the second coat and the third before bed.

Do first coat of poly on the counters, second coat on the cabinets and then second coat of poly on the main wood floor.

Just painted top of my table gray and also do not want to use a poly coat.

The top is sealed with three coats of wipe on poly.

A back vent is a nice detail but I wish this coat was full wool instead of a poly mix.

That inner lining is waterproofed, while the outer shell of the coat is just a thin layer of nylon or poly, and is about a waterproof as a cheap windbreaker.

Two hours later, the table top was ready for a light sanding with 220 grit sandpaper and the second coat of poly.

How many coats of the poly did you do?

With a touch of stretch, this fine Tommy Hilfiger sport coat is half - lined and features a slim, trim fit.52 % wool, 46 % poly, 2 % spandex.Two - button.

To finish, I added three coats of poly sanding with 400 grit between coats 1 and 2, for a nice smooth finish.

I typically don't sand between coats of poly, and it turns out with a great finish.

I then decided that instead of wax, I would do a top coat of Minwax water based poly.

I think I want to poly instead of wax as final coat but I wanted to apply dark wax for effect in some areas of my piece.

gave two coats and then distressed the edges and some of the details and then instead of waxing over it I did a Minwax water based poly that goes on easy and clear.

If you used a brand that allows you to do this (Annie Sloan is one) you can paint another coat over the wax, then seal the fresh coat of paint with poly.

This did not happen to me with a sample that had the dark wax over 1 coat of clear wax (which itself was over two coats of poly), but I don't want a dark wax look for these chairs, so I am just wondering if I should be trying something different to get this white wax to stick.

I'm sure with a good coat of exterior paint or poly any type of wood would hold up, right?

If you're sealing with a poly, sometimes mixing a bit of poly with the paint and doing a final coat before sealing it with straight poly will help with that.

The rim and eight legs all got about 3 coats of Olympic Gold, and all of it was protected with the MasterClear poly.

You can wet sand with 220 or higher wet sandpaper (its black) in between the coats of the poly to get a super smooth finish.

«Rime takes cues from games such as The Witness and The Wind Waker with a simple yet meticulous low poly look coated in beautifully vibrant splashes of paint.»

Visually speaking, Rime takes cues from games such as The Witness and The Wind Waker with a simple yet meticulous low poly look coated in beautifully vibrant splashes of paint.

- The hardwood guys came back yesterday to do the final coat of poly on the wood, but used the wrong sheen (matte instead of high - gloss).

I had them screened and two fresh coats of fresh poly laid down which will hopefully help keep them in good shape.

We didn't use a stain on the countertops; we just sealed it with a no - color poly and then used Waterlox (a food - grade sealant) and put multiple coats on of that.

You can wet sand with 220 or higher wet sandpaper (its black) in between the coats of the poly to get a super smooth finish.

So you first sealed with the no color poly (how many coats of the poly?)

We just did this in our living room that was 533 sq feet and did it for less than $ 500 (including the wood, liquid nail, stain, nails, all the tools, and 4 coats of expensive poly).

Then we used two coats of poly to protect it.»

After a human error (sharpie) I had to refinish one part of my table and ended up putting another coat of poly over the entire thing.

When I redid my old wood floors the suggestion for the poly was to put two coats of glossy poly on, followed by a coat of satin.

Another day and another coat of stain - and then she got a nice coat of poly!

I finished the entire top with a coat of flat poly just to protect it, because after all being able to really use a table and clean it is a necessity to make not only pretty but functional.

I am not a huge fan of Poly, I hate the smell, the dry time, the 3 coats you have to apply and the shiny hint it give to the piece, the BB Frosch wax will give it the same protection with out all the hassle of Poly.

Do you sand the last «Ok, this thing is done» coat of poly?

I believe chalk paint would work but you would need to add several coats of wax or a poly to protect it.

After two coats, I pulled off the tape and then gave them all a good coat of Minwax Poly.

I applied 3 coats of chalk paint on a test section, and when I applied my first coat of poly and some of the paint is lifting and I can see the original color underneath.