Once the device enters
into pairing mode, it will appear under «Other devices», as seen below.
As soon as you open the case for the first time the headphones
enter pairing mode, and every time after that all you have to do to connect is open the case.
The Go immediately goes into
pairing mode when powered on, making it easy to connect with a phone or tablet.
From here, you'll need to act quickly, since most Bluetooth accessories will automatically leave
pairing mode after about 60 seconds.
It is also used for putting the headphones into
pairing mode by holding down for a few seconds.
Once tuned on, you simply press and hold the power button to
initiate pairing mode, following the instructions on your smartphone, or tablet to complete the process.
When I go
into pairing mode, it just doesn't find the keyboard, to my mild annoyance.
Simply put your device in
Bluetooth Pairing mode, push and hold the button on top of the speaker, and pairing is done within moments.
• Headphones didn't show up, it took too long and now they're out
of pairing mode.
Pairing the speaker to your device is usually a challenge, but surprisingly the B2 went into
pairing mode upon being plugged in for the first time.
In some cases, I either pressed too slow or held too long and did something completely different from what I had intended, including turning the buds off or
re-entering pairing mode.
The BE Sport3 go into
pairing mode right after being turned on for the first time, making that process painless.
The bottom of the case has a single Lightning port for charging and on the back there's a button to enter Bluetooth
pairing mode on non-Apple devices.
If you take a little while to find the Bluetooth options, your AirPods might
leave pairing mode and you'll see the white blinking light stop.
The backing card in the blister pack will walk you through all the «combos» needed to boot the ZERO up in
different pairing modes.
With your console powered up, pairing the Retro Receiver with a Bluetooth - compatible wireless controller just requires you to push the single red button on the front of the adapter once the controller has been put into its
own pairing mode.
The Elite Sport immediately went into
pairing mode once we turned them on, with voice prompts guiding us step - by - step.
(The trick is that this version of the dimmer doesn't need to any
special pairing mode to connect, so SmartThings found it right away.)
The right ear cup has three multi-function buttons, allowing you to power the headphones on or off,
begin pairing mode, skip tracks, and control volume.
In order for your Android phone or tablet to view the controller listed as a possible Bluetooth connection, you will need to use a button combination on the PS4 DualShock 4 wireless controller to
access pairing mode.
Just place a Bluetooth device in
pairing mode near your PC and you'll see a notification asking you to pair it, so you won't even have to open the Settings app and navigate to Bluetooth settings.
State LED signalization Fob inactive LED off Button pressed LED lights up
1x Pairing mode (hold button for 5 sec) LED on Maintenance mode...
Linking one or more A50 headsets with the base station is as simple as pressing and holding the power button on each, which initiates a
brief pairing mode.
After installing the Martian Notifier app from the Google Play store (there's also a version for iOS), we
enabled pairing mode on the watch by tapping the bottom button a couple of times to get to its setup menu and then the top button once to check «Android.»
Next, you'll need to press the button on your Hue Bridge, which put the hub in
pairing mode so that the SmartThings app can communicate with it.
We ended up powering the earphones up and down a few times before successfully entering
pairing mode with the central multifunction button.
For the first time you will need to tap and hold the smart button to enter the Bluetooth
pairing mode then start the YU Fit app and follow the steps.
Bluetooth 5.0 rounds out the wireless support, and Google has added in a new
Fast Pair mode that works in conjunction with a number of different protocols on all products with the Made for Google badge on them.
If you press and hold down the button, you can initiate
Bluetooth pairing mode to connect to an iPhone or Android smartphone.
Pairing the earbuds is accomplished by inserting them into your ears and holding one of the two buttons to
activate pairing mode.
On iOS devices, you put the speaker into
pairing mode by pressing the Pairing button and finding SONY: SRS - X2 under Other Devices on the Bluetooth Settings screen.
However, unlike most headphones that greet a user with a welcoming chime or voice when turned on, as well as an indication
of pairing mode, these headphones do no such thing.
Subsequent device pairing requires you to hold down the Bluetooth button on the back for about 5 seconds to
initiate pairing mode.
Holding the multifunction button for about three seconds powers on the Halo Smart (holding it for five turns it off), which goes immediately into
pairing mode upon first startup.
You find the power button (which lights up to
indicate pairing mode, battery life), which is a bit flushed, as you go along the can, you find the curved volume rocker, and then near the bottom you find the play / pause, answer / hang - up button.
Just long - press the circular setup button again and your AirPods will
re-enter pairing mode and be discoverable from your other devices once again.
Bluetooth pairing isn't hard at all, since the Elite Sport go into
pairing mode right away.
For iOS devices, you can put the Mini Boom
into pairing mode by holding down the Bluetooth button on top of the speaker until you hear a chime, then finding UE MINI BOOM under Other Devices in Bluetooth settings.
Once you launch the app on your iPhone and turn on the watch you select
the Pair mode.