For the first time you will need to tap and hold the smart button to enter the Bluetooth
pairing mode then start the YU Fit app and follow the steps.
Not exact matches
The engine is
then paired with a racing - inspired 7G - DCT 7 - speed dual clutch transmission that offers quicker gear changes and selectable ECO, Sport and Manual
modes.
An M -
mode also allows you to save preferred combinations, and they can
then be easily accessed each time you enter the car via a
pair of steering - wheel buttons.
You'll need to put your car's stereo or dashboard system into Bluetooth
pairing mode,
then navigate to Settings > Bluetooth on your iPhone.
Start controller
pairing on my FTV Put DS4 into
pairing mode (light bar blinks to indicate
pairing) FTV sees controller Select controller with FTV remote to start
pair DS4 goes OUT of
pairing mode (almost as if it did
pair successfully) and LED blinks slowly a few times,
then turns off Turning DS4 back on causes the LED to flash white a few times
then turn off again.
The only solution is to open settings on the iPad, «forget» the Folio, turn off Bluetooth, turn off the Folio
then turn on the folio and put it into
pairing mode, turn on Bluetooth on the iPad, chose the Zagg Folio and
pair it.
The speaker only goes into
pairing mode if you turn it on and it can't find the device with which it was previously
paired; in other words, if you
pair it with your phone,
then want to
pair it with your tablet, you have to turn off your phone's Bluetooth to put the Anker back into
pairing mode.
To enter Bluetooth -
pairing mode, press the Xbox button to turn the controller on, and
then hold the sync button on the top of the controller for three seconds.4 We had no problems playing over Bluetooth during our testing, but there are some caveats: Your PC needs to be running the Windows 10 Anniversary Update or newer, Microsoft says only one Xbox One controller can be connected via Bluetooth at a time, and the controller's headset jack doesn't work.
You find the power button (which lights up to indicate
pairing mode, battery life), which is a bit flushed, as you go along the can, you find the curved volume rocker, and
then near the bottom you find the play / pause, answer / hang - up button.
Alternatively if your phone is one of the increasing amounts of Android phones that support NFC
pairing then you can connect your headphones by simply putting them in
pairing mode and tapping the rear of your phone against them.
You slide the power slider all the way to the right to put the headphones in
pairing mode, and
then you simply select them from your phone or laptop's Bluetooth menu.
A pleasant British woman will tell you that the single «bud is both on and in
pairing mode, and
then all you have to do is
pair the Muse 5 in your device's Bluetooth menu.
Then, turn on your Bluetooth keyboard and put it into
pairing mode.
One you remove the earphones from their case, you simply hold down both touch surfaces to put the Beoplay E8 into
pairing mode, and
then just select them from your device.
Just hold the button on each bud for a couple of seconds to turn them on, and
then keep holding to put them into
pairing mode.
Once they selected this option they can enter the Home into
pairing mode and
then head over to their phone's Bluetooth settings to add it, just like they would any other speaker.
With your sensors in place, you'll put the keypad into
pairing mode,
then pair everything up by pressing a button on each sensor,
then giving it a name on the keypad.
Just like on Android, all you need to do is turn on a peripheral, put it in
pairing mode, and
then place it near your Windows 10 PC.
You'll have to put that Bluetooth speaker into
pairing mode,
then you simply follow the instructions in the app.
After installing the Martian Notifier app from the Google Play store (there's also a version for iOS), we enabled
pairing mode on the watch by tapping the bottom button a couple of times to get to its setup menu and
then the top button once to check «Android.»
To do this, put your Bluetooth headphones into discoverable
mode,
then go to Settings > Bluetooth devices on your smartwatch, find the name of your headphones in the list, and complete the
pairing process.
To put it into
pairing mode, you press the Bluetooth button on left side of the speaker and
then find «Pocket Kick» on your mobile device's list of Bluetooth devices.
I like that over putting the doorbell into a
pairing mode and
then praying Wifi Direct actually works, because Wifi Direction often doesn't actually work on the first try.
If you have
paired them to a phone or another device before and maybe upgraded your phone or did a factory reset and need to
pair them again, just press the button on the right earbud until it turns on
then keep pressing it until it goes into
pairing mode.
However, you can
then pair up a Bluetooth mouse and keyboard, and once set to Productivity
mode through the coupled Android app, the Dell Cast builds a classic desktop - style...