Sentences with phrase «pilot hole»

If your exterior is wood, all you need to do is drill pilot holes using a drill bit that's a tad smaller than the included screws.

From there, drill four pilot holes with a power drill where the four screws will go.

Step 3: Make small pilot holes and then drill the wheels into place.

Drill pilot holes in pencil marks and insert knobs.

Drill pilot hole on top edge of back legs.

Step 5: Drill pilot holes from the top, through the shelf and into the top of the footboard.

Once you're happy with the arrangement, screw or hammer the hangers right through the paper (if you have plaster walls, drill pilot holes before inserting anchors or nails).

Drill a small pilot hole for each screw to avoid risk of splitting the wood.

Matz BM, Mesman M, Montgomery RD. Effect of pilot hole diameter on axial pullout of 3.5 mm self - tapping bone screw.

Drill pilot holes through the thickness of the 36 - inch board and into the end of the 18 - inch boards.

Drill two countersunk pilot holes about 3/8» from the edges of the top board.

Pre-drill pilot holes with countersink bit on bottom edge of all trim boards.

Get the look by screwing pilot holes in the ends of wooden light bulbs (available at a crafts store).

Three additional holes (2,912 ft) were drilled as RC pilot holes with core tails.

I also took one of the hooks and used it to cut pilot holes on each slat at 10 - inch intervals.

Early Sunday morning, Shell's Noble Discoverer drill ship sank a bit into the Burger Prospect, about 70 miles off the Alaska coast, the beginning of a 1,400 - foot pilot hole that will form the basis for a mile - deep exploration well.

Drill four pilot holes sized to wood screws through back of shelf into shelf.

Drill pilot holes around the perimeter of the wood, and secure with good construction screws.

Then I drilled a tiny pilot hole with my electric drill where each screw would go; I attached the hinges with a screwdriver.

Drill two very small pilot holes in each stick on each side to accommodate the cut tacks.

Drill pilot holes for D - ring hangers.

After gluing the the two pieces of wood in position with wood glue and holding the joint until it's reasonable stable, drill two pilot holes through the joint so the wood doesn't split.

Either use self tapping screws or drill pilot holes with countersink.

Drill pilot holes in the battens before fixing them in case you split them.

We (meaning Derek, I just stood there and took pictures), measured out the desired distance and drilled a pilot hole, which is a small guiding «starter hole» before you start putting holes in your grill lid with a giant drill bit.

You can also screw the Lexan sheet to the window frame instead of Velcro to get a more permanent solution, but first you will have to drill pilot holes.

Yesterday, Italian news agency ANSA quoted project coordinator Giuseppe De Natale of Italy's National Institute of Geophysics and Volcanology as saying that the office of Naples mayor Luigi de Magistris has approved the drilling of a pilot hole 500 meters deep.

The rig, owned and operated by the Nabors Drilling company and previously used to find oil or gas, first bit into the reddish soil here in July 2002, drilling a pilot hole 1.4 miles deep, which was outfitted with a string of seismometers.

Fasten the boards together as described below by first drilling a pilot hole.

We (meaning Derek, I just stood there and took pictures), measured out the desired distance and drilled a pilot hole, which is a small guiding «starter hole» before you start putting holes in your grill lid with a giant drill bit.

Carefully drill a pilot hole from the bottom of the base up into the «Y».

I started by drilling a pilot hole in the plaque to make screwing it into place easier.

For the back piece I drilled pilot holes and secured the pieces with screws and Gorilla Wood Glue.

If there is sufficient metal surrounding the bolt so fitting a larger bolt will not impact structural integrity centre punch it (so your drill bit won't slip)- drill it out and tap a new thread in 3 stages to accept a larger bolt.Use a pilot hole then ever larger drill bits.Not applicable in all cases; but one option that has stood the test of time

If you're going to drill a pilot hole big enough to get a grip on the remainder of the bolt, you're basically going to have to drill with a huge bit.

It's just as much trouble as drilling the pilot hole: there's still an obnoxiously tough bolt chunk where you want to put the replacement threaded insert.

A surgical drill is then used to drill a pilot hole to put the fixation screw into.

If you have a concrete or brick wall, use the included drill bit to make your pilot holes and hammer in the included wall anchors before you drive in the screws.

Step 6: Drill pilot holes and drive two screw eyes to the front and back.

Mark the location of the mounting hole above the opening and drill a pilot hole there.

Don't forget to drill your pilot holes and make sure the slat is level before attaching it to the right stud.

I had to drill some pilot holes as I went along.

Drive the dry - wall screws into the pilot holes, countersinking the heads in the wood base.

Pre-drilling the pilot holes helps your wood screws to grip better and keeps the wood from splitting when you put in the screws.

Drill pilot holes and attach screw eyes.

Drill a pilot hole in your dowel.

TIP: Always drill a pilot hole before drilling the screws into the wood.