Common - rail technology is used for the injection system, two
pumps building pressure up to 2000bar in the rails.
Not exact matches
As we
pump air through the water the
pressure inside the bottle
builds up until the force of the air pushing on the water is enough to push the cork out of the end of the bottle.
It's common to be under some
pressure when
pumping, because you need to get x amount of milk for your baby to feed, or you know you're going back to work in 2 months, or because you really need to
build your supply back after a challenge.
I started
pumping occasionally in order to
build up a stash (and relieve the constant
pressure of full boobs!)
And in at least one of the levees that caused flooding, there were actually areas where the levee was intentionally
built lower to the ground in order to protect the
pump stations by relieving some of the water
pressure.
Pressures within the arteries
build up, requiring the heart to
pump harder to push blood through the narrowed tubes to the lungs.
Use a bike
pump with a
built - in tire
pressure gauge to find the sweet spot.
I wouldn't totally rule out the fuel
pump, as it will have to work slightly harder with very little fuel in the tank, on top of already having to work extra hard to
build pressure in the fuel lines and supply enough fuel to get the engine started.
Somehow you have introduced a flow resistance that wasn't there earlier and the oil is taking a second or so longer to get from the
pump to the bearings to
build up
pressure to operate the sensor.
Pump the clutch to
build up
pressure (
pumping the clutch is referring to depressing it with your foot repeatedly to
build up
pressure in the hydraulic system, keep clutch depressed)
It is possible that some passages or filter is blocked and the oil
pump is not able to
pump enough oil to
build pressure.
The air suspension's
pump can get lazy with age, flashing a warning until
pressure is
built up.
4.2 liter stroker engine (103.6 mm x 82.4 mm) Secondary oil jets for pistons High
pressure oil
pump Cylinder head porting Special head sealing system and headstud upgrade CNC designed intake manifold Fuel system upgrade with 3
pumps 64 mm Titanium turbochargers Esmotor
built tiptronic transmission NEW rear wing carbon intake system (utilizing modified stock airbox) NEW 90 mm (3.5 inch) stainless x-pipe exhaust system Custom designed headers Water / methanol injection kit
Other details on the 2017 Chevrolet COPO Camaro include lightweight, adjustable coilover front suspension, four - link rear suspension with double - adjustable coilover shocks, Panhard bar and stabilizer bar, rear axle with an aluminum center section featuring a lightweight steel spool and 40 - spline gun - drilled axle shafts, lightweight drag - race manual four - wheel disc brakes, custom manual steering rack, fuel cell with
built - in high -
pressure fuel
pump and unique racing wire harness.
That is because, different than on the previous generation, for the first time an electric
pump is used to
build pressure.
Two electric
pumps are used to quickly
build up the oil
pressure, which can reach over 100 bar.
The two
pumps build up a
pressure of up to 2,000 bar in the rails.
An efficient gear - driven oil
pump builds up the control
pressure; when the car is driven off, it helps a suction jet
pump to cool the dual clutch.
Continuing to exceed the speed limit despite having to repeatedly
pump your brakes to
build up
pressure and even having to use the parking brake to slow yourself down...
Wireline operator / rigger with experience performing bond log and gamma ray, pipe recovery / chemical cut, plug setting, perforating /
pump downs, fishing, gun
building, tool maintenance,
pressure control, and much more
PUMPS AND METERS, Rainbow, TX 6/2012 to Present Pipefitter Welder • Lay out, fabricate, assemble, and install piping systems and fixtures • Install equipment for steam, hot water, heating and cooling systems, and industrial systems • Read blueprints to select materials according to job specifications • Plan installation sequences and thread and end pipes with a pipe bending machine • Use cemented, wiped, soldered, chalked, or threaded joints to assemble and join piping • Secure pipes and piping systems with hangers, brackets, and clamps • Use
pressure building to test piping systems for leaks • Repair and maintain pipe systems and components and secure pipes to radiators and tanks • Select materials such as supports, hangers and hydraulic cylinders according to each work process