Sentences with phrase «screw holes on»

It doesn't look like there are any screw holes on any part of the MDF.

Step Two: Mark the screw holes on the wall or unit you will be mounting the light too.

Not exact matches

This TV stand does away with the furniture part of the equation in favor of two legs that you'll screw into the holes on the back of your TV so that the TV can stand on any old table.

We used a No Holes kit on the banister so we did not have to screw or drill any holes into the banister Holes kit on the banister so we did not have to screw or drill any holes into the banister holes into the banister post.

The side that doesn't slide will only have screw holes in the legs and not on the bars.

I pre-drilled small holes on the backs + simply screwed them in.

A big hole in the seat, water damage from being left out on the porch, joints coming apart where the screws had rusted through.

There should be a pro red rubber boot over the positive connection, and something filling these screw holes, just like Larry remembers seeing on a Yukon.

I need to attach the number plate on the front of my Mazda but I can't just put screws through as the holes are rectangle (see picture).

I've done the same thing working on carbs (tiny butterfly screws, for instance) and most effectively when helicoil or other thread insert work on spark plug holes.

TreatStiks ™ are tubes with screw - caps on one end and small holes near the other.

Players can only screw the mini-screen into the output holes on the back of the console to activate it.

I've used a large pickle container (the Warehouse size) on counter with a few red wrigglers thrown in on top of leaves or shredded mail and then just put scraps in and cover with a lid pierced with some air holes... if fruit flies are a problem, a cloth or paper towel with rubber band or screw you nail pieced lid right over.

And the wall plate it comes with, while it has two holes for screws, has them in a nonstandard configuration on the left and right sides, not on the top and bottom like you'd want in order to mount it to a receptacle in place of a switch.

On the top of the Play: 1 there is a physical Play / Pause button, volume rocker and a status LED light, while the back has a stand mounting screw hole.

Furthermore, the dual speakers have five - hole speaker grills (rather than six or more, as seen on current iPhones), and the tiny screws flanking the Lightning port seem to be missing.

If the exterior of your house is brick or masonry, you'll need to use the included drill bit to drill holes where you made marks, and then insert in the two yellow wall anchors before screwing on the mounting plate.

This final type of cooler contains a backplate and requires you to screw the cooler on using four mounting holes on the motherboard.

There's a familiar shutter button on the top right and a 1 / 4 - inch screw hole for a tripod on the bottom.

On the top can be found a speaker grill, which comes in handy for two - way audio and for sounding an alarm, while on the bottom you'll find a screw - hole for mounting the camera to a tripod or another type of bass, if you so choosOn the top can be found a speaker grill, which comes in handy for two - way audio and for sounding an alarm, while on the bottom you'll find a screw - hole for mounting the camera to a tripod or another type of bass, if you so chooson the bottom you'll find a screw - hole for mounting the camera to a tripod or another type of bass, if you so choose.

Make sure your camera will connect to your tripod — that hole on the bottom of your camera screws onto your tripod in most cases, so be sure it fits.

Thread the light fixture wires through the center hole and screw on the mounting nuts to the mounting screws.

He drill a big hole on the wall then we pushed that special screw in.

BTW, the old rack is going from forest green to a bronzy brown with previous «pecan» warped wood top to natural wood top with «peg holes» (read: turned over top, filled old screw holes with wood filler, then used dark furniture crayon on top, and LOTS of polyurethane of course!)

I may be too late in responding, but we have these blinds too and replacement windows; however, we screwed the brackets into the window frame not directly to the window using the hole on the top of the bracket rather than the holes at the back of the bracket, so you could go that route...

Only problem was the handles that were previous on everything had two screw holes.

Mr. Project installed one on the wall with pocket - hole screws, and then installed the second one to the first one with pin nails.

Pre-drill the screw holes and use a 1» to 1-1/4» wood screw on 1 - 1/2» thick tops (at least 1» of screw should go into the butcher block or wide plank top).

If you push the ends where the holes are, and the screws will go into, down in ink then put them on your piece you will see the markings in the correct place so you know where to drill for your holes.

Insert the screws on the holes directly touching the Lazy Susan round.

After the anchors were added, we put the board back on the ceiling, lined up the holes in the board over the anchors, and added screws to secure the board in place.

Modern flat pack carcases (think Ikea or B&Q) tend to be made on a CNC machine, which improves the chances that all holes and screws will line up.

Assemble the legs by drilling a pilot hole on top edge of back legs, screw back legs to front legs as shown in diagram with 2-1/2» trim screws and glue.

We pre drilled a small hole and then screwed the hook in, and on the inside of the cabinet the hook is held up by a washer and a nut.

The only thing I don't like about ours is that our screw holes are actually nail holes and the nails have a habit of popping up on occasion.

Lay the sheet of wax paper on top of the extra wood piece and run screws through predrilled holes and into the extra wood piece.

Predrill the holes for the hooks, then use the screws in the package to install them on the bottom of the memo board.

I used pocket holes on the back of the plywood that go into the 4 × 4 legs, and long pocket screws.

Drill pocket holes on the back side of the front piece and connect the sides with 1-1/4 ″ pocket screws and glue.

We attached on the underside with 3/4» pocket holes and 1-1/4» pocket hole screws, but again, countersinking screws or nails would work too.

We built our face frame first on the ground with 3/4» pocket holes and 1-1/4» pocket hole screws, then nailed the whole thing to the front of the project.

After these rods dried, we pre-drilled holes for the hooks and screwed those in, one on each pole is fine.

Measure up on all four legs where you want your shelves and secure them with pocket hole screws and wood glue.

Anchor screws into the drywall (preferably directly into a stud) and hang your brackets onto the screws (ours came with pre-drilled holes on the back).

Then we attached the joints and drilled a hole for the screw on the side of the board.

On mine, the screw threads for the bulbs went through the base of the shade, so I knew that the holes in my cups had to be larger than that.

Once the template created, I could just tap a nail through the holes on the template to indicate where the screws would go to attach the hardware.