Sentences with phrase «stitch along that edge»

Then I ironed them flat and did a straight stitch along the edges.

Step 8: Top stitch along the edge, close to the ruffle for a finished look.

The stitching along the edge of the band contrasts well with the leather, giving the whole band a much more defined look.

Not exact matches

After the zipper was sewn in, she sewed the facing to the top edge of the dress, folded the seam allowance under along the facing's zipper edge and hand stitched it in place.

Stitch about 1/4» from the cut edges along the curve.

Stitch along the inner folded edge, leaving an opening to thread the elastic through.

Stitch along blanket 1/8 ″ from edge, securing the pom pom trim as you go.

Some ring slings have padding where the sling rests on the caregiver's shoulder or along the edges of the sling, and some depart further from traditional shawl carriers by having the fabric at the end of the sling folded and stitched into a rope - like tail.

Sew the fabric with a straight stitch along the two curved edges — following the pin line shown below.

Use a needle and thread to sew a wide basting stitch along the bottom of the fabric edge.

We folded the fabric in half then laid down the stitched palazzo with the long edge along the fold.

Measure up 1/4 ″ from the trim and with your embroidery floss, stitch a running stitch along the bottom edge of the towel.

I hand - stitched the skirt onto the dancer, using a standard stitch at the top and a ladder stitch along the sides so that the edges would tuck under.

Then, I took a white pencil to outline the shape I wanted around the shark print and used a tight zigzag stitch along the pencil lines to finish off the edges and prevent fraying of the shark overlays.

Along with the great Lift / Wheel / Tire selections, this Custom Rubicon is loaded with many other quality aftermarket components such as: *** EXTERIOR *** - Signature Commando Green Exterior Finish - MetalCloak Aluminum Fenders w / outer edge finished in Black - Lifted Off - oad Hood w / Rugged Ridge Hood catches - Lifted Off - road Grille - Fab Fours Front Bumper with Stinger - SmittyBilt X20 10K winch with FairLead - SmittyBilt Recovery Hook - SmittyBilt 3/4 D - Rings w / Daystar Isolators - DV8 Inner Fender Liners - AMP Research Power Side Steps - SmittyBilt Rear Tire Carrier *** LIGHTING *** - ProComp Headlights - Rugged Ridge Smoked Tail Lights - Rigid Industries 2x2 LED Dually Light cubes mounted to the A - Pillar * LIFT and SUSPENSION - TeraFlex 4 Lift Kit - TeraFlex Front Steering Stabilizer - Exhaust Spacer Kit WHEELS and TIRES - 20 Fuel Beast Wheels - 37/12.5 r20 Nitto Trail Grappler Tires ** INTERIOR *** - Custom Premium Eleganza Heated Leather Seating in Black w / Green contrast stitching - RED LED Rocker Switch - Alpine System A Alpine 7 ILX - 107 / 207 or INE - W960HDMI Touchscreen Reverse / BackUp camera w / mount IdataLink (3x Lock to start) remote start integration - Starwood Motors All Weather Floor Liners - Starwood Custom Billet Badge - AEV ProCal Module * For all inquiries please contact Starwood motors at 888-464-7174 *

Crimson red stitching can also be found on the dash, shifter boot, center and door armrests, and along the edges of the center console.

In works such as Tracey» sbouquet (At Swim Two Birds)(2011), created for an artist who once sent Bowling a bouquet of flowers, a bordering of delicate painted lace along with a stitched edge represents Bowling's open - ended approach to painting.

You can attach your trim along the very edge of the collar (as in the Anthrologie jacket) or you can attach your beaded trim just under the topstitching so the original stitching remains visible.

With right sides together, pin and machine - stitch (1 cm seam allowance) along a 20 cm edge.

Fold each strip in half along the length and stitch the long raw edge and one end, taking a 1 cm seam.

Cut a length of decorative trim or braid to the width of the blind and slip stitch in place along the bottom edge.

To create a dowel pocket along the bottom edge, stitch a second line of stitching 6 mm from the raw edge.

Machine stitch along tacking through all layers as close to the folded edge as possible.

Stitch a 1/4 inch seam along the bottom edge and trim the excess part of the zipper.

Step 4) To hem the facing strip, turn under 1 cm then 1.5 cm along one long edge and stitch.

Step 4) Machine stitch along the sides and top edge taking a 2.5 cm seam and (if your headboard is shaped like ours) rounding around the corners a little as you go.

Top stitch along the long edges.

Machine stitch along one short end and along the long edge taking a 1.5 cm seam, leaving the remaining short end open.

Turn under 1 cm then 1.5 cm along the top edge of the pocket and top stitch close to the folded edge.

Lay the Stitch Witchery along the edge of the burlap and line the lace up over top.

Stitch all round taking a 1.5 cm seam and leaving a 50 cm gap along one long edge.

You are going to start off by taking 2 strips of different colors and place right sides together and stitch along the top (you can finish each edge with a Serged or Zig Zag stitch as you go or when you have attached all the strips of fabric together).

Press and top stitch along one short and one long edge.

Stitch the strip to the card along the outer edge, backstitching at both ends to secure the stitches (Figure 1).

Taking 2.5 cm seams, stitch each short edge and then from each corner along the long raw edge for 55 cm, leaving a gap of 55 cm in the centre.

Along the remaining short edge turn under 1 cm then 3 cm and top stitch to hem.

Step 3) Right sides facing fold the fabric in half along the length and stitch along the long raw edge taking a 5 cm seam.

Step 8) Pin the pocket centrally to the front of the apron and top stitch in place along the sides and bottom, 1 mm from the pressed - under edges.

Pin and stitch a strip of Velcro along each edge.

Step 6) Slip stitch along all the pinned edges and remove pins.

Turn under the raw edges along each short, cut edge, machine or hand stitch and press.