Sentences with phrase «use wood screws»

If you would like to make it that strong use wood screws to assemble your ladder.

Pre-drill your holes, then use wood screws to secure it to your window frame (or in my case — the bottom of open shelving.)

Now, use wood screws to attach the bottom and top shelves.

Once the sides were done, we used wood screws at the base of the bookcases to attach them even more securely to the 1 × 6 boards.

Using wood screws we hung the cabinets on the wall.

Note: use a wood screw that is 3/4 ″ — 1 ″ long for a secure hold.

B) Attach the top using wood screws through the bottom side of the top of the base.

Not exact matches

Great tip from Dee: to replace a Dutch oven lid use a long screw and nut with a flat tipand a large wood thread spool.

Use it with Velcro around your bed slats, with straps underneath your mattress and on top of your box springs, or simply screw it into the frame of any wood bed for maximum support.

Using screws and a drill, attach four lengths of wood to the sides of the table.

Requirements for wood screws and other fasteners - eliminate the use of wood screws that serve as the primary method of attachment on key structural elements; also includes other fastener requirements to address incidents related to loose hardware and poor structural integrity;

You should also take into account the best way to mount models onto your rods; the Science Buddies wind tunnel uses models carved out of balsa wood, into which threaded casings may be drilled so that they can be easily screwed onto the rods.

I placed one screw every 11 - 12 inches and used wood glue before screwing them together.

If you're drilling into wood studs, the way to go about mounting it is simply using 1 / 4 - inch lag screws (to fit into 3 / 8 - inch mounting holes).

did you use any wood filler to conceal the screws holding the tops / bottoms?

Use a polyuerthane - based glue (try Gorilla Glue) to attach rocks to old drawer knobs, then screw the knobs into a plank of wood and mount it on a wall at eye - level in an entryway.

We used small trigger clamps to hold the wood panels to the doors and screwed six wood screws to each panel from the back of the door.

We used 1-1/2 inch wood screws for this.

I have a question; what size of wood screws did you use?.

Clean the cabinet door using the Krud Cutter prepaint cleaner and patch the screw holes using the FamoWood latex wood filler.

We just took 3 pieces of scrap wood (1 × 6 or 1 × 8 probably) and cut them all to the same length (maybe 15 ″ wide or so), then used smaller scraps (1 × 2) as braces along the back and put screws in them to hold it all together.

You can just add the screws from the outside of the box (rather than having them hidden inside the pocket holes) or even use a hammer and nails and wood glue if you don't own many power tools.

Use wood glue and 1 1/4 ″ screws to attach the legs to the skirt as shown.

The metal device screws onto the bottom of a door allowing a person to pull it open with details, descriptions, photos, specifications of hardwoods, rare woods, exotic, domestic woods used in fine custom, handmade knife handles

Now the C - clamp seems to be stuck in the caliper (reading now, I should have used a wood block or one of the old pads rather than screwing the C - clamp directly into the piston), the screw top rotates, but doesn't move the screw shaft.

«You have to use special screws designed for either pressure - treated wood or cedar.»

Durham started using everyday objects including a range of materials from wood to PVC piping, metal screws and TV screens, which would become central to his practice in the following decades.

Instead of creating slick installations, Sibony uses basic materials — drywall, wood, screws, paint, canvas, etc. — that are openly revealed, thereby becoming autonomous and elevated in their import much like Rauschenberg's works.

It came as a result of a challenge to make a bicycle using no bolts or screws, just wood and glues.

Originally hailing from the UK, industrial designer - turned - natural - builder Jeffrey built this geodesic dome cabin using recycled wood, earthen plaster and other various local materials that he collected as it became available, ultimately taking him two months and costing only $ 200 for nails, screws and roofing material.

If your exterior is wood, all you need to do is drill pilot holes using a drill bit that's a tad smaller than the included screws.

Couple and assemble wood parts into sections, patterns or models using bolts, screws, nails or glue

Fit and fasten wallboard or drywall into position on wood or metal frameworks, using glue, nails or screws.

Assemble and fasten materials to make frameworks or props, using hand tools and wood screws, nails, dowel pins, or glue

We used varying sizes of wood screws depending on the depth of the wood being attached.

BTW, the old rack is going from forest green to a bronzy brown with previous «pecan» warped wood top to natural wood top with «peg holes» (read: turned over top, filled old screw holes with wood filler, then used dark furniture crayon on top, and LOTS of polyurethane of course!)

You can just add the screws from the outside of the box (rather than having them hidden inside the pocket holes) or even use a hammer and nails and wood glue if you don't own many power tools.

To join the pieces, I used wood glue and screwed the seam in place with another (scrap) board overnight to hold it in place while it dried.

Next, you can go ahead and secure your tabletop to your table base with wood screws using the pre-drilled pocket holes.

Attach the leg using 1 1/2» pocket hole screws and wood glue.

Step 1 - Use screws to attach a strip of plywood down the sides of the fireplace, then create a mantel out of MDF or whatever kind of wood you'd like...

Step 3 - Use screws to attach your mantel to the cleat and to the wood strips running down the sides of your fireplace...

Pre-drill the screw holes and use a 1» to 1-1/4» wood screw on 1 - 1/2» thick tops (at least 1» of screw should go into the butcher block or wide plank top).

From the bottom, drill a countersink hole and attach using a 1-1/4 ″ wood screw.

Instead, I screwed the wall hanging to the wall in those locations and then used Blue Tack to stick the wood slice covers over the screws.

Determine the location of each rung and attach the rung to each side board using two wood screws.

Attach the back legs flush to the back panel using 1 1/4» pocket hole screws and wood glue.

Attach the dividers between the two front legs using 1 1/4» pocket hole screws and wood glue.

Attach the legs with the side panel using 1 1/4» pocket hole screws and wood glue.

Using wood glue and 2» wood screws attach the top to all 4 legs.