Sentences with phrase «used wood glue»

For these sections I used wood glue and clamped the two pieces together to ensure a tight bond while drying.

I used wood glue, but as I said before, one of the long dowels already snapped off, so you would probably be better off with gorilla glue or liquid nails.

I used wood glue and my staple gun to attach the embroidery hoops together.

I cut the trim on my miter saw and used wood glue and tape to hold the trim pieces in place while I secured them with the brad nailer.

Once my holes were drilled, I used wood glue to attach the top piece of wood to the bottom piece and then used clamps on the ends to secure the wood while the glue dried.

I used wood glue and a nail gun.

My 1 × 4 was going to be my shelf, so I used some wood glue and glued my 1 × 3's together and used clamps to hold them in place while they dried.

I used wood glue and a nail gun to attach the panels to the frame.

To assemble I used wood glue, putting the glue on the smaller piece and not too close to the edge so once clamped the glue wouldn't squish out.

I also used wood glue for extra adhesion.

I didn't have a nail gun when I did this project back in 2007, so I just used wood glue to hold everything together.

To join the pieces, I used wood glue and screwed the seam in place with another (scrap) board overnight to hold it in place while it dried.

My staple gun was nowhere to be found, so I used wood glue to affix it to the frame.

I used wood glue for this step, but you could probably use the Liquid Nails here, too.

Then I just used wood glue to adhere it to the frame.

we used wood glue and clamps to make the counter tops, and that was it!

Because I wanted this project to be done in one day, I went the somewhat lazy easy route and used wood glue.

I placed one screw every 11 - 12 inches and used wood glue before screwing them together.

You can then use simple 1x4s cut to mimic the shape of your pocket doors and glue them onto the front using wood glue and clamps.

This glue is a great choice for anyone looking for a cheap and easy to use wood glue that really gets the job done right.

(not really noticeable) Also I would strongly recommend that you use wood glue or some type of strong glue to permanently lock your squares into place if not your unit will be pretty wobbly and you can see the gaps of where the squares slide in.

After it dries just use some wood glue and glue the X and O onto your painted board.

Once you have it cut, use your wood glue and glue the X together, just not to the base yet!

Use wood glue and 1 1/4 ″ screws to attach the legs to the skirt as shown.

Assemble the box using wood glue, with the drilled 6 - by - 5 1/2 - inch piece attached to a 5 1/2 - by - 5 1/2 - inch piece on either side.

Use wood glue and brad nails to attach to the bottom of the drawer box.

From totally tossable to multi-functional organizer using wood glue, power tools and a bit of elbow grease.

The next step was to attached the trim pieces using wood glue and finish nails.

Using wood glue and brad nails, nail the plywood onto the horizontal 16 1/2» 1x2's from the INSIDE of the nightstand.

Use wood glue and finish nails to nail them onto the back, holding all your other boards together.

I tried to nail the crown molding pieces to my 1 ″ x6 ″ pieces, but after splitting a couple of pieces of crown, I finally decided to just use wood glue.

Step 6) If using wood glue, clamp the pieces where they intersect.

After the spray paint is dry, use wood glue and a «cut tack» (ours came from Lowes) to attach a plastic mirror rosette to each «cross-section».

We had some trim and scrap wood so he used that and put the ledges together using wood glue and clamping them together.

You could use wood glue between the joints, just to give it a little more sturdiness if you would like.

Using wood glue and 2» wood screws attach the top to all 4 legs.

Using wood glue and a paint brush, glue all the wood pieces together, starting with the two center pieces and working your way out -LCB- I used two small pieces to form the point / bottom of the arrow -RCB-

3 Using wood glue and screws, attach a strip of MDF to each side off the armoire at the bottom so that the top of the strip is level with the bottom of the front frame of the armoire.

Use wood glue to attach the decorative appliqués (optional).

Using wood glue and our nail gun, we installed (2) 1» x 2» guides on the inside of the exterior cabinet and (1) 1» x 2» guide on the outside of the drawer.

Step 7: Put it all back together, but use wood glue between the cut pieces of table leg and the bowls.

Step 4: Using your wood glue and pipe clamps, glue the 2 × 6's together.

You definitely will want to use wood glue — I used Elmer's Wood Glue.

Before attaching the apron, be sure to use wood glue and attach the 2 — 1 x 3 @ 51 ″ together.

Step 2: Use wood glue to glue the letters together.

and Before attaching anything with screws, use wood glue and clean up excess with wet rag!

Then Pookie laid the lumber out on the floor of our garage, using wood glue along each rabbited edge, and allowed it to thoroughly dry.

* Use a wood glue when assembling dovetail drawers.

You could also use wood glue if you do not have a Kreg jig.

Step 2 — Glue the wood scraps together using wood glue.