Variable valve timing, which
uses hydraulic pressure on the camshaft pulley to change the point in the engine cycle when the intake valve opens and closes.
The wet multi-plate clutch system
uses hydraulic pressure to actuate the clutches and provide for gear selection.
Loss of Hydraulic Pressure: The brake system
uses hydraulic pressure to push the brake pads against the rotors.
Magna - steer
uses hydraulic pressure and magnets to turn the wheels.
Our tester included the optional Kinetic Dynamic Suspension System, which
uses hydraulic pressure to disengage the front and rear sway bars during certain conditions, allowing for greater articulation on the trail.
Conventional steering
uses hydraulic pressure to help the driver turn the wheel.
Basic automatic transmission function is
it uses hydraulic pressure, valves, switches and clutches to shift up and down.
As you may know, transmissions
use hydraulic pressure created by the transmission fluid...
The Xtronic design allows continuous change of the transmission gear ratio by connecting the two pulleys with a metallic belt and changing their diameter by
using hydraulic pressure.
Not exact matches
The almonds are pressed
using a
hydraulic cold - presser that applies a large amount of
pressure to extract the maximum amount of milk from each nut.
Gas turbines are also attractive because natural gas is relatively cheap and abundant, due in part to the introduction of
hydraulic fracturing technology, or fracking, which
uses high -
pressure water to extract hydrocarbons from previously inaccessible shale deposits.
Hydraulic fracturing, or fracking, is a method of hydrocarbon recovery that
uses high -
pressure injections of fluid to break apart rock and release trapped oil and natural gas.
Dasgupta
uses powerful
hydraulic presses to partially melt rocks and minerals to simulate what is happening under equivalent
pressures in the mantle.
According to Gupta, who is part of the research team, StimuFrac consistently outperformed conventional fluids
used for
hydraulic fracturing and «is believed to have lower critical pore invasion
pressure that provides further advantage over conventional fracking fluids.»
The almonds are pressed
using a
hydraulic cold - presser that applies a large amount of
pressure to extract the maximum amount of milk from each nut.
There are a few quirks to get
used to — the brake pedal isn't a pedal, it's a touch - sensitive, pyramid - shaped rubber button where
pressure, not pedal travel, equals stopping power; the feedback - free,
hydraulic rack - and - pinion steering is as disconnected and consistent as a rheostat, and it feels like that of no other car on the planet — but the sharp - yet - pillowy ride and handling combination is almost supernatural.
The lifters
use oil from the engine to create a
hydraulic pressure in them to keep them in contact with the valvetrain.
It then
uses that information to control
hydraulic pressure to the brakes and control wheel slip.
Both aluminum and steel production Corvette frames are hydroformed, a process that
uses high -
pressure hydraulics to form complex shapes.
Hi There, Your car's power steering system works by
use of
hydraulic pressure that runs through the pump which is powered by the motor by a belt.
The brake system
uses pressure from
hydraulic fluid to operate these components, applied to the piston in the Ford brake caliper.
The Cadillac brake caliper
uses its piston, operated with
pressure provided by a
hydraulic fluid system, to move the brake pads inwards to make contact with the brake disc.
If the
pressure switch is attached to a
hydraulic line, you'll need to
use two wrenches to remove it.
As you know, automatic transmissions
use transmission fluid to lubricate internal parts and create
hydraulic pressure inside which...
They primarily
use hydraulics to select gears, depending on
pressure exerted by fluid within the transmission assembly.
Whereas traditional VTEC operation changes valve opening duration based on higher oil
pressure during high rpm operation at one side of the valvetrain's rocker arms, the Civic's i - VTEC system can switch valve timing duration at low rpm and low oil
pressure using two
hydraulic actuators on both sides of the intake rocker arm.
Cars
use hydraulics to help the driver apply
pressure to the brakes.
The C5 and C6 frames
used hydroformed side rails — single pieces of steel tubing running the full length of the frame, bent into shape via internal
hydraulic pressure.
Both brake types
use a
hydraulic braking system as well as a brake pad or brake shoe to create friction and cause a vehicle to stop when the driver applies
pressure to the brake pedal.
All brakes
use a
hydraulic system, wherein fluid moves through brake lines to create
pressure which presses the brakes pads against the rotors and stops the car.
This transmission, called a CVT, is designed to have no discernible shift points; it
uses a set of pulleys and a metal drive belt to go from low - to high - range,
using a
hydraulic system that works at twice the
pressure of a standard automatic transmission.
The braking system in your vehicle
uses a pressurized flow of
hydraulic fluid to apply
pressure to a piston in the Chrysler brake caliper, causing it to squeeze the brake pads into contact with the brake disc.
The hybrid system
used by Nissan boosts steering input with
hydraulics, but maintains
pressure using an electric pump, thereby avoiding sucking power from the engine.
The electronic stabilization program ESP also
uses high - precision
hydraulic valves, which control
pressure build - up with great accuracy.
Although throttle, steering, and braking are all in someway or another computer controlled, the CR - V's all - wheel - drive system is controlled by simple
hydraulics that
use pressure supplied by pumps on the front and rear axles to determine torque split.
Employing a pair of
hydraulic swivel motors (incorporated into each axle assembly), the DCC
uses fluid
pressure to essentially turn the Cayenne's sway bars into a pair of variable - rate longitudinal dampers.
Automatic transmission fluid This is typically an oil - based fluid
used in a transmission that lubricates and cools the transmission provides
hydraulic pressure to shift gears automatically.
This is the
hydraulic fluid
used to transmit
pressure through the brake lines in a brake system providing stopping power and protecting
hydraulic brake components from internal corrosion.
[53] This is
used along with the car's torque converter to build up
hydraulic pressure before launch.
Brake fluid This is the
hydraulic fluid
used to transmit
pressure through the brake lines in a brake system providing stopping power and protecting
hydraulic brake components from internal corrosion.
Abstract: The principle of an electro -
hydraulic servo - driven control valve
used to regulate mixed - gas
pressure in combined cycle power plant is introduced.
In this process, water is pumped at high
pressures to fracture underground hot rock reservoirs similar to technology
used in natural gas
hydraulic fracturing.
Fracking, or Fracing as the oil and gas industry ungrammatically spells it, is short for
hydraulic fracturing, and the technology is now being
used extensively to extract shale gas, by pumping liquids at high
pressure into the rock, creating and expanding fissures.
According to the studio, less energy and only one - quarter of the amount of wood are
used to manufacture a conventionally sized board of material,
using a
hydraulic press that forms it with 400 tons of
pressure.
The wave system is based on a
hydraulic power take - off system,
using a double function piston pump to transform the energy from the wave into water
pressure that is then sent through a turbine, thus generating electricity.
PUMPS AND METERS, Rainbow, TX 6/2012 to Present Pipefitter Welder • Lay out, fabricate, assemble, and install piping systems and fixtures • Install equipment for steam, hot water, heating and cooling systems, and industrial systems • Read blueprints to select materials according to job specifications • Plan installation sequences and thread and end pipes with a pipe bending machine •
Use cemented, wiped, soldered, chalked, or threaded joints to assemble and join piping • Secure pipes and piping systems with hangers, brackets, and clamps •
Use pressure building to test piping systems for leaks • Repair and maintain pipe systems and components and secure pipes to radiators and tanks • Select materials such as supports, hangers and
hydraulic cylinders according to each work process