Sentences with phrase «vacuum pump leaking»

Today we are diving into the 2.5 L vacuum pump leaking oil.

The funny thing is, this vacuum pump leaking is often mistake for a leaking rear main seal.

Not exact matches

Things I loved: ~ didn't drown my daughter - she can eat at her pace ~ even though there are 3 parts to the nipple, it's still very easy to take apart and clean ~ due to vacuum pressure being needed, milk does not leak out ~ my daughter switches seamlessly between this bottle and my breast then back again ~ uses the same bottles that Medela pumps use I was worried about trying this bottles at first due to the price being high and seeing reviews about other babies not taking the bottle.

I am leaning towards fixing my repairs (leaking vacuum pump) and keeping the car versus selling it.

I have a VW GTI 2011 dealership says the vacuum pump seal gasket is leaking And can not get one for another 3 to 4 weeks does this sound right?they claim it has to be made in Germany and shipped over here.

When the 2.5 l vacuum pump fails it will cause an engine oil leak.

Are you talking about vacuum pipes that are used to move the flaps that control the flow of hot / cold air into the cabin, or are you talking about using a vacuum pump to test if your A / C refrigerant pipes are leaking?

Some Examples: Air filter clogged Exhaust leak plugged cat clogged fuel injector malfunctioning fuel pressure regulator clogged fuel filter malfunctioning fuel pump spark plugs, wires, cap, rotor, coil Vacuum leak dirty throttle body malfunctioning fast idle thermo valve (similar to vacuum leak) low oil (unless there is an oil level sensor) belts gaskets seals rings low compression bearing damage (rod knock) Broken cam rocker fell / broke off broken valve spring stuck valve critical engine damage (windowed the block) wiring, fuses, relays starting system - ignition switch, starter, relay Cooling system - clogs, leaks, flow (may throw a code if you overheat) transmission clutch (es) driveshaft, differential, axles brakes suspension tires hvac lights Vacuum leak dirty throttle body malfunctioning fast idle thermo valve (similar to vacuum leak) low oil (unless there is an oil level sensor) belts gaskets seals rings low compression bearing damage (rod knock) Broken cam rocker fell / broke off broken valve spring stuck valve critical engine damage (windowed the block) wiring, fuses, relays starting system - ignition switch, starter, relay Cooling system - clogs, leaks, flow (may throw a code if you overheat) transmission clutch (es) driveshaft, differential, axles brakes suspension tires hvac lights vacuum leak) low oil (unless there is an oil level sensor) belts gaskets seals rings low compression bearing damage (rod knock) Broken cam rocker fell / broke off broken valve spring stuck valve critical engine damage (windowed the block) wiring, fuses, relays starting system - ignition switch, starter, relay Cooling system - clogs, leaks, flow (may throw a code if you overheat) transmission clutch (es) driveshaft, differential, axles brakes suspension tires hvac lights gauges

All say there is no vacuum leaks, power to the pump, everything reads fine..

If I removed this air pump and shut off valve, the vacuum line would be open, which I think may cause vacuum leak.

Extensive amounts of time are used to detect vacuum leaks without testing for proper operation of the EVAP leak detection pump.

Stalling at idle could be due to a faulty mass airflow sensor, faulty camshaft or crankshaft position sensors, worn spark plugs, wires or defective ignition coil (s), inadequate fuel delivery or pressure (clogged fuel filter, injectors, faulty fuel pump or pump circuit), contaminated or old gasoline, defective throttle position sensor, faulty idle air control valve, leaks in the EGR system, intake vacuum leaks, and so forth.

There are several possible sources that trigger these two codes including a faulty fuel pressure regulator, weak fuel pump, clogged fuel filter, faulty powertrain control module, vacuum leak, faulty injector (s), faulty oxygen sensor (s) and a faulty mass air...

Rough idle and excessive shaking of the engine could be due to a bad tank of gasoline, dirty fuel injectors, incorrect idle speed, exhaust restrictions, vacuum leaks, incorrectly installed or damaged spark plugs, a defective or clogged fuel pump or fuel filter, failing electrical components such as the ignition control module, plug wires, coils, and spark plugs, a defective airflow sensor, dirty oxygen sensors and other causes.

However, if all cylinders are affected, you would test, in turn: the fuel pressure regulator, fuel pump pressure, check for a clogged fuel filter, vacuum leak, faulty oxygen sensor (s) and faulty mass air flow sensor.

The poor operation that you are describing could be due to a bad tank of gasoline, dirty fuel injectors, incorrect idle speed, exhaust restrictions, vacuum leaks, incorrectly installed or damaged spark plugs, a defective or clogged fuel pump or fuel...

The lack of response to the accelerator pedal has quite a few potential causes that would have to be sorted out in a diagnostic including, just as a few examples, plugged fuel injectors, faulty oxygen sensors, fuel pump and / or filter, vacuum leaks including that caused by a faulty EGR system, ignition system malfunctions, bad valve timing if the timing belt or chain is worn or skipped, blocked exhaust (e.g., catalytic converter fails or becomes clogged), a faulty airflow sensor or throttle position sensor, and so forth.

Loss of power on acceleration can be due to plugged fuel injectors, faulty oxygen sensors, fuel pump and / or filter, vacuum leaks including that caused by a faulty EGR system, ignition system malfunctions, bad valve timing if the timing belt or...

The causes include vacuum leaks and EGR system faults, a faulty idle air control (IAC) valve or circuit, faults in the fuel pump control circuit, defective...

Rough idle can be caused by dirty fuel injectors, incorrect idle speed, exhaust restrictions, vacuum leaks, incorrectly installed or damaged spark plugs, a defective or clogged fuel pump or fuel filter, failing electrical components such as the ignition control module,...

Tags for this Online Resume: high vacuum, turbo molecular pump, radio frequency, helium leak detection, mechanical, facilities, training, abatement, toxic, poison, emergency response, team, chiller, regularor, power, ion, manufacturing, cleanroom, field service, quality, safety, auditor, travel, chemicals, gas, robotics, electro, magnetic, controller, leader

Technician • Read, understood, and utilized electrical and mechanical schematics and diagrams • Trained and guided junior engineers, technicians, and staff members • Utilized electrical test and repair equipment including DVM, oscilloscopes, hand tools, drill press, hydraulic press, calipers, micrometers, and vacuum leak detectors • Maintain and repair all company equipment including ultrahigh vacuum crystal growing machine, computer control system, hydraulics system, and harmonic drive • Performed preventative maintenance on chillers, cooling towers, pumps, chemical distribution systems, HVAC, and waste treatment system • Oversaw electrical equipment including breakers, transformers, and diode bridges

Professional Duties & Responsibilities Read, understand, and utilize electrical and mechanical schematics and diagrams Trained and guided junior engineers, technicians, and staff members Planned, scheduled, and directed maintenance and technical response teams Proficient in electrical test / repair equipment including DVM, oscilloscopes, hand tools, drill press, hydraulic press, calipers, micrometers, and vacuum leak detectors Maintain and repair all company equipment including ultrahigh vacuum crystal growing machine, computer control system, hydraulics system, and harmonic drive Performed preventative maintenance on chillers, cooling towers, pumps, chemical distribution systems, HVAC, and waste treatment system Oversaw electrical equipment including breakers, transformers, and diode bridges Repaired and maintained packaging equipment, conveyor systems, high water pressure systems, refrigeration units, and other food industry equipment Worked with AC - DC motors, Servo drive, chain and metal belts, and gear boxes Ability to adapt mechanical and electrical knowledge to a variety of industries