Sentences with phrase «with hydraulic lifters»

This generation also offered a revised 1.3 - liter inline four - cylinder engine used in the Pontiac Firefly, with multi-point fuel injection (with hydraulic lifters and lash adjusters, and a 30,000 - mile service interval).

Nissan SR18DE is equipped with hydraulic lifters, so you do not have regulating valves.

1G - FE wasn't equipped with hydraulic lifters so every 10,000 - 15,000 miles of mileage (20,000 km) you had to adjust the valves.

They use variable valve timing system on intake camshafts, and also they are equipped with hydraulic lifters.

MR20DE was not equipped with any hydraulic lifters, and so if ticking noise has appeared, you need to regulate valve clearance.

In 2000 RB20DE was upgraded with new crankshaft, improved intake system, modified head with no hydraulic lifters, another ECU.

This head is equipped with the hydraulic lifters.

The head is not equipped with hydraulic lifters, so from time to time you should regulate valve clearance, once you hear metallic rattle.

The cylinder head is the same as in the 2AR, it is DOHC equipped with hydraulic lifters, a variable valve timing system (Dual - VVTi).

What you are describing sounds like the noise associated with hydraulic lifters which are a part of the valve train.

This engine has not been equipped with hydraulic lifters, so be ready to regulate the valves every 60,000 miles of mileage (100,000 km).

It is on Windansea Beach, has a rooftop pool and spa, a garage with a hydraulic lift ideal for a sports car.

The felony complaint says the teenager was operating a skidloader with a hydraulic lift and fork attachment, which is prohibited under child labor laws.

So, the guys rent a U-Haul truck with a hydraulic lift helping to secure the casket.

Truck is equipped with a hydraulic lift gate.

On the front axle, the shock absorbers are equipped with a hydraulic lifting system, which enables the front end of the super sports car to be lifted by 40 millimeters at the touch of a button, simplifying its ability to negotiate minor obstacles.

The hotel is paraplegic friendly and all floors are serviced with a hydraulic lift and serviced by surveillance cameras.

It is then floated out to sea, where the telescopic tower is lifted with hydraulic lift jacks on a single working platform.

Safely handle and drive a 26 - foot box truck with hydraulic lift gate.

Not exact matches

SOT 1:06 The system for recovery involves attaching and raising the ship by remote control of the underwater robotics guided with the use of cameras and electronic sensor systems and a hydraulic lifting system that will lift the wreck and bring it to the surface — if possible without damaging it.

The French parliament voted on June 30 to ban the controversial technique for extracting natural gas from shale rock deposits known as hydraulic fracturing, or fracking, the web sites of Le Monde and other French media reported.The bill had already passed the National Assembly, the country's lower chamber, on June 21, and on June 30 a Senate vote of 176 to 151 made France the first country to enact such a ban, just as New York State is preparing to lift a moratorium on the same method.The vote was divided along party lines, with the majority conservative party voting in favor and the opposition voting against the bill, according to Le Monde.

Compared to the normal LaFerrari, the FXX K's V - 12 engine has new camshafts with mechanical (rather than hydraulic) lifters, specially polished intake manifolds, and a new exhaust that lacks any mufflers.

When minimal drag is ideal and at low speeds, the wing sits flush with the rear bodywork; at higher speeds, it is lifted via two hydraulic struts, generating downforce.

He's running a Comp Cams hydraulic 252H cam with.425 lift and 252 duration.

The gasoline engine is a 2.0 - liter turbocharged four - cylinder that uses twin - scroll turbos, Continuously Variable Valve Lift technology, electro - hydraulic valve control, variable intake valve lift, direct injection, and an exhaust manifold that's integrated with the cylinder head castLift technology, electro - hydraulic valve control, variable intake valve lift, direct injection, and an exhaust manifold that's integrated with the cylinder head castlift, direct injection, and an exhaust manifold that's integrated with the cylinder head casting.

TechArt's 718 nose lift comes with the firm's sport spring kit, the whole package consists of lower and firmer front and rear springs (as well as a helper spring for the front axle), two hydraulic cylinders and a hydraulic pump unit.

It is also fitted with climate control, a full infotainment system with Bluetooth integration, a front axle hydraulic lift and tyre pressure monitoring system.

There's something adolescently awesome about driving a truck with a plow on it, shoving snow into a pile, lifting the blade with a whine of hydraulics, and going back for another pass.

Rear - axle steering — as found on GT3 models — also joins the options list, while a hydraulic lift system raises the nose 40 mm to cope with speed bumps and steep driveways.

The lifters use oil from the engine to create a hydraulic pressure in them to keep them in contact with the valvetrain.

The 6 cylinder engines have had challenges with the HVA (hydraulic valve actuators or lifters)...

We also add a set of brand - new Vortec iron heads and a hydraulic flat - tappet camshaft with 0.435 / 0.460 - inch lift specs.

Engine Type: Chevy Small - Block V - 8 Displacement (cu in): 350 Bore x Stroke (in): 4.000 x 3.480 Block (P / N 10105123): Cast - iron with 4 - bolt main caps Crankshaft (P / N 14088526): Nodular iron Connecting Rods (P / N 10108688): Powdered metal steel Pistons (P / N 12514101): Cast - aluminum Camshaft Type (P / N 24502476): Hydraulic flat tappet Camshaft Lift (in):.435 intake /.460 exhaust Camshaft Duration (@.050 in): 212 ° intake / 222 ° exhaust Cylinder Heads (P / N 12558060): Vortec iron; 64cc chambers Valve Size (in): 1.940 intake / 1.500 exhaust Compression Ratio: 9.1 nominal Rocker Arms (P / N 10089648): Stamped steel Rocker Arm Ratio: 1.5:1 Water Pump (P / N 88894341): Cast iron, long - style Flexplate (P / N 14088765): 12.750» Recommended Fuel: 92 octane Ignition Timing: Base 10 ° BTDC, 32 ° Total Maximum Recommended rpm: 5,500 Balanced: External

It included a high torque common rail diesel engine, top speed of 150 km / h, 1.3 tonnes cargo capacity, monocoque full steel body, compact 2850 mm wheelbase, modular armour plate including a mine deflector plate on the vehicles floor, adjustable variable lift front and rear coil - over air shock absorbers with maximum 450 mm of ground clearance, hydraulic braking system with four ventilated disc brakes, EADS vehicle data recorder system, EADS integrated communication system for UHF or VHF bands, EADS integrated mobile command, control and information system; EADS jamming system.A10 Warhog

VK45 heads were equipped with continuously variable valve timing control system (CVTCS) on intake camshafts, and also they used hydraulic lifters.

Pro Eagle's 2 - ton Beast off - road jack features large, non-pneumatic wheels that allow it to roll over uneven terrain with solid steel axles and sealed bearings that exceed the hydraulic lift capacity of the jack.

It is powered by a 1990 Ford Mustang 332ci engine that has been resurfaced and is equipped with an Eagle crankshaft, internally balanced Mahle forged pistons, COMP Cam hydraulic lifters, timing gears and chain, and a stock Ford EFI system.

Suspension Springs & Such: 3 - link with coil springs and Bilstein 5100 shocks (front); Trail Gear leaf springs (rear) Tires & Wheels: 39.5x13.5 - 15LT Super Swamper Iroks on 15x10 Pro Comp steel rims Steering: PSC hydraulic ram, Saginaw steering box, stock pump Other Stuff: Racer X race radio, Smittybilt XRC10 winch, Vision X LED lights, custom tube bed, Powertank PT - 10, 60 - inch Hi - Lift jack

It was a 300 hp version of the 350 cu in small - block, with 10.25:1 compression and hydraulic lifters.

Type: R Cubic Inches: over 440 Bore: 4.32 inches plus.40 over, total of 4.72 Block Modifications: bored.040 over Block: Chrysler Bore x Stroke: stock 4.72 x 3.75 Rods: stock, cast Pistons: Speed - Pro, 9.8:1 compression Crankshaft: stock steel Cam: Comp Cams hydraulic Lift:.470 at.050 224 Valves: Milodon, 2.14 intake, 1.81 exhaust Valvesprings: Comp Cams Rocker Arm: stock Intake Manifold: Edelbrock Aluminum Six Pack Carburetors: Holley Six Pack Distributor: Mallory Exhaust: Chrysler RB Hi - Performance Muffler: Spin Tech Exhaust Pipes: Muffler Tech Performance Inlet / Outlet Size: 2.50 inches Exhaust: aluminized 2.50 inches Exhaust Tips: stainless steel tips with YearOne red inserts Engine: built by VanGordon Racing Engines (Upland, CA)

Description: (1) heavy - duty heat - treated.060» for use in Gen - VI 454 and 502 engines with hydraulic roller lifters

«First, all of these passenger - car engines have hydraulic lifters, therefore a milder cam than the mechanical cam used in the ’57 performance models and secondly, you'll notice that 9.5 to 1 is the maximum on compression, even with the injector.»

The cylinder head incorporates dual overhead camshafts with four valves per cylinder and maintenance - free hydraulic lifters with low - friction roller - finger followers.

Assembled with hydraulic roller valve springs: Closed seat pressure 135 # @ 1.850»; Open seat pressure 365 # @ 1.250»; Max lift.700»

Will also fit non-roller cam 289, 302 and 351W blocks when used with tie - bar aftermarket hydraulic roller lifters

To make it easy to drive in steep parking structures or garage entrances, Porsche offers a hydraulic lift system with integrated lifting cylinders in the struts of the front axle.

The Boss engine makes 507hp (at 6,500 rpm) and 450lb - ft (at 5,100 rpm) in an 8.2 - deck Boss block with a Scat forged crank and forged I - beam rods, Mahle forged pistons, a fairly healthy hydraulic roller cam (232/240 duration at.050 lift,.580 /.602 lift), aluminum Z2 heads, and 10.2:1 compression.

The ASA camshaft is a hydraulic roller with.525 - inch lift on both sides, along with 226 degrees duration on the intake side and 236 degrees on the exhaust side.

Classic K - 10 Monster Vehicle: 1972 Chevy K - 10 Owner: Jeff Meadows Location: Tucson, Arizona Chassis: Stock Engine: Built 383ci stroker Chevy V - 8, Patriot aluminum cylinder heads, 10:1 compression, MSD 6A ignition, Hooker headers, Flowmaster mufflers Drivetrain: SM465 four - speed manual, Pro Fab T - Case, Dana 60 front with ARB air locker, Dana 60 rear with ARB air locker, 5.38 gears Suspension: Full custom arched leaf springs for 36 inches of lift, Fabtech Dirt Logic reservoir shocks Steering: Full Hydraulic steering Brakes: 1 - ton brakes Tires / wheels: 19.5 x 54 - inch Super Swamper Boggers on custom 20x10 steel wheels Interior: Original interior with custom Pioneer JL head unit, Amp and subwoofer Others Parts: Fluidine radiator, lowered headlights and custom mud flaps to keep it street legal Favorite Off - Road Area: Southern Arizona and Glamis

The cams act directly on hydraulic lifters on the ends of the valves and are fed with a lubrication passage drilled through the cylinder head lengthwise.