Sentences with phrase «deck height»

Cylinder block deck height didn't change and it is 202 mm.

Does it not seem odd that the bias of buckets, deck heights etc would produce a variation similar to half the climate signal over the same period?

The hood was redesigned with a bulge reminiscent of the original 240Z to accommodate the raised deck height of the new VQ35HR.

It is similar to the EJ20 cylinder block, but diameter of cylinders was increased to 99.5 mm, cylinder block deck height remained the same (201 mm).

Longitudinal.002», Transverse.0012», Overall.004», Minimum deck height from the top of the main bearing journal to the deck is 7.4511» It's an interference motor... if modifications have been made to the valve train, pay close attention to your installed valve height of 1.2795.

She is especially proud of the low rear deck height, which neatly conceals the retractable top, and the longer rear overhang balancing the shark nose jutting over twin kidney grilles that are canted on a slightly negative plane.

Deck height choices include 9.2 in (234 mm) and 9.5 in (241 mm).

The engine's blocky deck height was so tall that it forced designers to raise the Titan's hood, which in turn meant they had to heighten the bedsides out back, too, to keep it from looking disproportionate.

Huang does use the word «spurious» in reference to ship deck height (which increased over time) introducing a spurious cooling effect in the bucket records.

Additionally, in two weeks we will be in production with our revolutionary FAAST TEC» tiny home trailer, featuring, the first ever torsion bar independent suspension, resulting in a 14 1/2 inch deck height and, potentially, a 12 ′ ceiling, Also, our trailer has our proprietary convertible, adjustable, building platform which can easily conform to any width from 3 1/2 ″ to 6 ″.

[3] It sold in low volume (less than 15 % of the HSC engines built) and was costly due to the tooling changeover required for the taller engine block deck height.

Deck height remained the same, 225 mm.

To accommodate those big, free - breathing valves while preserving the 100 mm cylinder - bore spacing that allows this all new block to be machined alongside the 5.0 - liter in Windsor, Ontario (the deck height is also the same), the bore was increased to 94 mm by eschewing iron liners in favor of a plasma - transferred wire - arc cylinder liner technology.

EDIT: this ain't Porsche:) but I'm reading in Porsche 911 the deck height should be between 1 and 1.5 mm, with a 75 mm bore

The more stroke an engine has, the less RPM the engine is capable of for a given deck height, which means that more stroke means more deck height or less RPM.

And the more the deck height rises, the longer and potentially heavier the rods have to get, which introduces its own set of constraints.

In this cylinder block, the bore was increased to 89 mm, and the deck height was left unchanged at 235 mm.

A new compact aluminum cylinder block with the deck height of 230 mm was used here.

It has the same V6, its deck height is 235 mm, but the engineers have increased the cylinder bore to 90 mm.

EZ30 engine was created completely from scratch, and it used aluminum Flat - 6 cylinder block with cast - iron sleeves, 2 mm thick, cylinder block deck height is 202 mm.

This is a typical 60 ° V6 engine with a compact aluminum cylinder block, its bore spacing is 98 mm, and the deck height is 235 mm.

The D15A cylinder block was made of aluminum and had cast iron sleeves, and its deck height was 207 mm.

Released in 1998, it had a smaller bore and stroke than the 2 - liter four - cylinder «Neon» engine; and, since the company already had bigger V6 engines, the cylinder spacing and deck height were both made much smaller, at 104 mm and 210 mm respectively, than those of the 3.2 / 3.5 engines.

This engine was created on the base of the 1.5 - liter aluminum D15A cylinder block, but the engineers increased its deck height to 212 mm.

All Low Block B - series engines have a 3.375 in (85.7 mm) stroke, a 9.98 in (253 mm) deck height and 6.358 in (161.5 mm) connecting rods, resulting in a 1.88:1 rod ratio.

The higher the deck height, the shorter the house.

The trailer measurements are considered to be part of the overall structural measurements and because there are laws around how tall your tiny house can be, you don't want the deck height to take away height from your house.